Wap SQ 10 Gallon Instructions De Service page 3

PLEASE READ THE ASSEMBLING THE
OPERATING CLEANER
INSTRUCTIONS AND
OBSERVE THE SAFETY CAUTION!
PRECAUTIONS! On delivery, the
accessories - except the
extension tubes
INTENDED USE packing of the cleaner) -
are lying in the tank and
When employed in must be removed before
accordance with their the cleaner is used for the
intended use, the first time.
industrial vacuum cleaners Remove the cleaner top
described in these section:
operating instructions are The power cord must not
suitable for picking up yet be inserted into a plug
non-flammable dry dusts socket.
and liquids. They • Open the retaining
correspond to dust class clamps and lift off the
'L'. cleaner top section
(Fig. 2).
• Place a bag-type filter
DESCRIPTION (Fig. 1) into the tank as
described in the
1 Handle instructions (printed
2 Appliance switch on the filter).
3 Suction force • Fit the cleaner top
regulator 1) section and close the
4 Retaining clamp retaining clamps.
5 Dirt tank 1) • Connect the suction
6 Inlet fitting hose. The 'Wap
7 Compressed air MultiFit' enables any
connection 1) Wap suction hoses
8 Appliance plug socket (27, 32, 36, 50 mm
9 Compressed air diameter) to be
supply 1) connected to the
10 Filter cleaning knob cleaner.
11 Warning light (Fig. 3).
12 Base frame 1)
ELECTRICAL/
COMPRESSED AIR
CONNECTION
The operating voltage
shown on the rating plate
2
must correspond to the
voltage of the main power
supply.
• Ensure that the
cleaner is switched
1) (in the off and insert the plug
of the power cord into
a properly installed
and fused plug socket
with ground.
CONNECTING ELECTRIC
TOOLS
SQ 10 Gallon AS/PE
SQ 17 Gallon AS/PE 2:
• Connect the electric
tool to the appliance
plug socket on the
control panel (Fig.4).
Before connecting a
tool, ensure that
both the cleaner and
the tool are
switched off.
For maximum power
consumption of the
electric tool to be
connected, see table
'Technical Data'.
CONNECTING
PNEUMATIC TOOLS
SQ 10 Gallon AS/PE:
• Connect the
pneumatic tool to the
quick coupler on the
control panel.
1)
• Connect the
compressed air supply
to the nipple (Fig.4).
1) Option/model variant
Before connecting a filter should always be
tool, ensure that installed in the tank. It is
both the cleaner and then easy to dispose of
the tool are the material picked up
switched off. and the service life of the
For the working main filter element is
pressure of the significantly increased. Dry
pneumatic tool to be cleaning without bag-type
connected, see table filter is also possible.
'Technical Data'. Inflammable substances
must not be picked up
SQ 17 Gallon AS/PE 2: with the cleaner!
• Connect the After picking up liquids,
pneumatic tool (two the filter element is damp.
tools can be Damp filter elements can
connected at the same clog more quickly when
time) to the quick dry substances are picked
coupler on the control up. For this reason, the
panel. filter element should be
• Connect the dried or replaced before
compressed air supply picking up any dry
to the nipple (Fig.1, substances.
Pos. 9).
Before connecting a
tool, ensure that PICKING UP LIQUIDS
both the cleaner and
the tool are Before picking up liquids,
switched off. the bag-type filter must
For the working always be removed from
pressure of the the tank.
pneumatic tool to be Inflammable liquids
connected, see table must not be picked up
'Technical Data'. with the cleaner!
If foaming is observed,
stop work immediately
WARNING: and empty the tank.
To avoid risk of elecrical
shock, do not expose to
rain. SWITCHING ON THE
CLEANER
PICKING UP DRY SQ 10/17 Gallon
SUBSTANCES SQ 10/15 Gallon RDF
SQ 10/15 Gallon RDFD
Before picking up dry • Turn the switch to
substances, the bag-type position 'I' (Fig. 5).
1) Option/model variant
SQ 10 Gallon AS/PE
SQ 17 Gallon AS/PE 2:
Two operating modes are
possible:
Switch position 'I':
The cleaner motor starts
immediately.
Switch position 'auto':
The cleaner motor starts
only when the tool
connected to the
appliance plug socket is
switched on (Fig. 6).
CAUTION!
Before turning the
switch to position
'auto', ensure that the
tool connected to the
appliance plug socket is
switched off.
The motor speed and thus
the suction power can be
varied at the suction force
regulator. This permits a
precise adaptation to
different substances to be
picked up (Fig. 6).
FILTER CLEANING
SQ 10/15 Gallon RDFD:
Warning light (Fig. 10)
indicates filter element is
in need of cleaning.
• Move filter cleaning
knob up and down.
This will move the ring
brush, cleaning the
filter element.
3