Milwaukee 48-22-8560 Manuel De L'utilisateur page 3

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Item
Description
Quantity
Side handle
Tool hanger
Swivel caster with
brake
Rigid caster
Bumper
Cord Storage
Brackets
Peg Board Bracket
NOTE: Begin product assembly close to the fi nal
intended location of your bench. This product is
heavy and may be diffi cult to move after assembly.
Attaching the Side Handle
Attach the side handle to the bench using four bolts
(CC).
NOTE: The holes in the bench are tapped and do
not require nuts.
Installing the Casters
Two people may be required to
CAUTION
complete installation.
CAUTION
Do not overtighten the screws.
1. Ensure all bench drawers are securely locked into
place using the key lock on the bench.
2. Lay the bench on its back. Use the packaging
material to protect the fi nish.
3. Mount the four swivel casters with brake to the
bench using four bolts (EE) and washers (DD)
per caster. The swivel casters with brake should
be installed on both ends of the bench.
1
1
4
2
4. Mount the two rigid casters in the middle of the
bench using four bolts (EE) and washers (DD)
per caster.
4
2
2
5. Tighten all bolts securely with a wrench.
6. Return the bench to its upright position.
Installing the Drawer Liners
Place the drawer liners in appropriately sized draw-
ers to protect the surface. The double sided tape
provided can be used to secure the drawer liners
and prevent them from sliding.
Installing the Bumpers
Attach the four bumpers to the bench using two
screws (FF) per bumper.
Installing the Cord Storage Brackets
Attach the brackets to the bottom right of the bench
power strip with two screws (AA) per bracket. Orient
the brackets with one pointed up and one pointed
down so that the power outlet cord can be wrapped
around the brackets for storage.
4
Attaching the Tool Hanger
Attach the tool hanger to the left end of the bench
using two bolts (CC).
Attaching the Storage Shelf
Attach the storage shelf to the bench using two
bolts (CC).
Positioning the Peg Board
Do not hang any objects on the peg
CAUTION
board without securing the board
in place.
The peg board is shipped and secured in its stored
location. To raise the peg board to a usable height,
remove the locking thumb screws at the top of the peg
board slides. The peg board can be raised to either
mid or full height position by pulling straight up. When
in mid or full height position, two pairs of ball detents
will temporarily hold the peg board in place. The lock-
ing thumb screw holes and the tapped holes located
in the frame of the peg board will align. Reinstall the
locking thumb screws to secure the peg board.
CAUTION! The locking thumb screws must be
installed before hanging objects on the peg board.
For increased stability of the peg board, peg board
brackets and hardware are provided. To install
brackets, locate the tapped holes on both ends of
the peg board, just above the bench work surface.
Mount the peg board brackets on both ends of the
peg board frame using two bolts (CC) per bracket.
With the foot of the bracket resting in position on the
wood work surface, mark the position of each bracket
hole and drill 1/8" holes approximately ¾" deep. Use
bolts (BB) to secure the peg board brackets to the
wood work surface.
Reversing the Wood Work Surface
The wood work surface comes pre-installed with
the bench. After wear and tear, the surface may
be reversed to use the clean bottom surface. To
reverse, remove the eight screws from the top of
the wood work surface, fl ip surface, and reinstall
the eight screws.
OPERATION
To avoid injury or property damage,
WARNING
do not exceed maximum shelf and
drawer capacity. Use care when moving bench
on incline or rough surface. Bench may tip if
weight is not evenly distributed front to back and
side to side. Place more than half the total load
weight on the bottom drawers when possible.
Locking and Unlocking the Bench
NOTE: The drawers must be fully closed before
locking/unlocking the unit.
Insert the key. Turn it fully left to lock, or fully right
to unlock. Always remove the key after locking and
unlocking.
Moving the Bench on an Incline or
Rough Surface
Take care that the bench
does not tip or become un-
balanced when moving it on
an incline or rough surface.
Do not exceed an incline of
10 degrees. Lock the bench
and secure all items before
moving.
Using the Caster Brakes
To lock the swivel casters, step down on the levers
marked ON. Be sure to lock all casters to prevent
bench from rolling or swiveling. To unlock casters,
push down on the levers marked OFF.
Rolling the Bench
The bench is only intended for rolling short distances.
Only roll the bench using the handle. Do not push or
pull bench by the frame or product may tip. Do not
modify the bench in any way. Drilling holes or modi-
fying the bench will lower the load capacity, which
can cause the bench to collapse, resulting in injury.
Lock the bench and secure all items before rolling.
Lifting the Bench
The bench is not intended to be lifted. However, if you
need to lift, empty the bench and then place straps
or forks inside and next to casters. Do not lift loaded
benches. Be sure all bystanders are moved away
before lifting bench.
Mounting Chargers
The rolling cabinet comes equipped with four pre-
installed charger mounting bosses, located below
the power strip. The charger mounts are suitable for
holding MILWAUKEE M18™ & M12™ Multi Voltage
chargers as well as M18™ chargers. To mount a
charger, install a screw (AA) into each boss, then
slide the charger's key-hole slots over the screws.
Slide the charger toward the fl oor to lock it onto the
screws.
Removing the Drawers
1. Fully extend and empty the drawer.
2. Depending on the side, either lift or lower the
release lever on both sides so the slides can ride
over the stops. Pull out to remove.
Release Lever
Installing the Drawers
1. Pull the slides and slide carrier out until fully ex-
tended.
2. Hold the slide on the cabinet while aligning it with
the slide on the drawer.
3. Slightly insert one side and repeat for the other
side.
4. Slowly push the drawer until it is fully closed to
engage the slide.
5. Open and close the drawer to verify proper op-
eration.
5

Publicité

Table des Matières
loading

Table des Matières