Traxxas TSM TQ TOP QUALIFIER Manuel Du Propriétaire page 16

MENU TREE
The menu tree below shows how to navigate through the
TQi transmitter's various settings and functions. Press and
hold MENU to enter the menu tree, and use the following
commands to navigate through the menu and select options.
MENU: When you enter a menu, you always start at the top.
Press MENU to move down the menu tree. When you
reach the bottom of the tree, pressing MENU again will
return you to the top.
SET: Press SET to move across the menu tree and select
options. When an option is committed to the transmitter's
memory, the status LED will rapidly blink green.
BACK: Press both MENU and SET to go back one level in the
menu tree.
EXIT: Press and hold MENU to exit programming. Your
selected options will be saved.
ECHO: Press and hold SET to activate the "echo" function. Echo
will "play back" your current position on the Menu Tree,
should you lose your place. For example: If your current
position is Steering Channel End Points, holding SET will
cause the LED to blink green twice, green once, and then
red three times. Echo will not alter your adjustments or
change your position in the programming sequence.
Below is an example of how to access a function in the menu
tree. In the example, the user is setting the Multi-Function knob
to be a Steering % (Dual-Rate) control.
To set the Multi-Function knob to control STEERING % (DUAL-RATE):
1. Switch the transmitter on.
2. Press and hold MENU until the green LED lights. It will blink in single intervals.
3. Press SET. The red LED will blink in single intervals to indicate Steering
Sensitivity (Expo) has been selected.
4. Press MENU twice. The red LED will blink three times repeatedly to indicate
Steering % (Dual-Rate) has been selected.
5. Press SET to select. The green LED will blink 8 times fast to indicate
successful selection.
6. Press and hold MENU to return to driving mode.
Restoring Factory Defaults:
When programming your transmitter, you may feel the need to
start over with a clean slate. See Selecting Your Model Profile on
page 6 for instructions.
*Torque Control is a feature designed only for use with the power system in the Traxxas Funny Car Race Replica (Model #6907).
Enter Programming
Press and hold
MENU for 3 seconds
1
Multi-Function Knob Press
SET
One Blink Green
Press
MENU
2
Channel Setup
Press
SET
Two Blinks Green
Press
MENU
Press
MENU
3
Mode Selection Press
SET
Three Blinks Green
Press
MENU
4
Traxxas-Link Press
SET
Four Blinks Green
* 4-Channel transmitter only
Press MENU to move through options.
Press SET to select an option.
1
Steering Sensitivity (Expo)
One Blink Red
2
Throttle Sensitivity (Expo)
Two Blinks Red
Press MENU to move through options.
3
Steering % (Dual Rate)
Press SET to select an option.
1
Three Blinks Red
4
Braking %
Four Blinks Red
2
5
Throttle Trim
Five Blinks Red
3
6
Knob Disabled
Six Blinks Red
7
Torque Control*
Seven Blinks Red
8
4
TSM
Eight Blinks Red
1
Press
Steering (Channel 1)
SET
One Blink Green
1
2 Press
Throttle (Channel 2)
SET
Two Blinks Green
2
3
Shift (Channel 3)*
Three Blinks Green
4
3
Front T-Lock (Channel 4)* Press
SET
Four Blinks Green
5
Rear T-Lock (Channel 5)*
Five Blinks Green
4
Press SET to select an option.
1
Electric
One Blink Red
1
2
Nitro
Two Blinks Red
1 1
Model Locking
Press
SET
One Blink Green
2
Press
3
MENU
2 1
Press
Delete Model
SET
Two Blinks Green
Note: The transmitter is "live" during programming
so you can test the settings real time without having
to exit the menu tree.
Servo Reversing
Press SET to reverse
servo direction.
One Blink Red
Sub-Trim
Use knob to adjust
sub-trim. Press SET to save.
Two Blinks Red
End Points Use steering wheel to
adjust. Turn right to desired
Three Blinks Red
end point, press set to save.
Turn left to desired end point and press set to save.
To reset max throw: Let go of controls and press SET.
Reset End Points
Press SET to restore factory
default end points.
Four Blinks Red
Servo Reversing
Press SET to reverse
servo direction.
One Blink Red
Sub-Trim Use knob to adjust
sub-trim. Press SET to save.
Two Blinks Red
End Points Use trigger to adjust. Pull
back to desired end point,
Three Blinks Red
press set to save. Push
forward to desired end point and press set to save.
To reset max throw: Let go of controls and press SET.
Reset End Points
Press SET to restore factory
Four Blinks Red default end points.
Servo Reversing
Press SET to reverse
servo direction.
One Blink Red
Unlock
One Blink Red
Lock
Two Blinks Red
Unlock All
Three Blinks Red
C onfirm Deletion
One Blink Red