EINHELL GC-MM 52 I AS Mode D'emploi page 38

Danger!
Sound and vibration
L sound pressure level ........................ 97 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ..................... 113,9 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Operation
Vibration emission value a
K uncertainty = 1.5 m/s
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
5. Assembly
5.1 General information
5.1.1 Fitting the steady grip (Fig. 3)
Fit the steady grip (Item 3a) as shown in Figure 3.
Do not tighten the screws until you have set the
perfect working position with the carrying strap.
The steady grip should be aligned as shown in
Figure 1. To dismantle, proceed in reverse order.
5.1.2 Fitting the long handle (Fig. 4a – 4b)
Pull the locking lever (A) and push the long hand-
le (Fig. 4b/Item 2a) into the connecting piece of
the engine unit. While doing so, make sure that
the drive shafts on the inside of the long handle
slide into each other (turn the spool head slightly,
for example, if required). The lug of the locking
lever (A) must latch into the hole (B). Now tighten
the handle screw (21) as shown in Figure 4b.
Anl_GC_MM_52_I_AS_SPK9.indb 38 Anl_GC_MM_52_I_AS_SPK9.indb 38
= 6.0 m/s
2
h
2
- 38 -
GB
5.2 Trimmer/scythe
5.2.1 Fitting the blade guard hood (Fig. 5a-5b)
Important: The cutting blade guard hood (Item
15) must be fi tted when you want to work with
the cutting blade. The guard hood for the cutting
blade must be installed as shown in Figures 5a-
5b. When doing so, make sure that the lug C slots
into the hole D on the long handle (Item 2a). Then
fasten the two socket head screws tightly using
the hexagon key (Item 30).
5.2.2 Fitting/Replacing the cutting blade
The fi tting of the cutting blade is shown in Figures
6a – 6g. To dismantle, proceed in reverse order.
•
Important! The cutting blade has sharp edges.
You therefore need to wear protective gloves
when handling the cutting blade.
•
Fit the carrier plate (22) onto the spline shaft
(Fig. 6b)
•
Securely fit the cutting blade (18) on the co-
ver ring (Fig. 6c)
•
Place the pressure plate (23) over the thread
of the spline shaft (Fig. 6d).
•
Plug on the cover of the pressure plate (24)
(Fig. 6e).
•
Look for the hole in the carrier plate, line up
with the notch underneath, lock with the sup-
plied hexagon key (29), and tighten the nut
(25) (Fig. 6f/6g). Note: Left-hand thread
•
Remove the cutting blade guard (Item 18a)
before starting work.
5.2.3 Fitting the cutting line guard hood to
the blade guard hood
Important: The cutting line guard hood must be
additionally fi tted if you want to work with the cut-
ting line (Fig. 7a/Item 14).
The guard hood for the cutting line must be ins-
talled as shown in Figures 7a – 7b. A blade (Fig.
7a/Item F) on the underside of the guard hood
automatically cuts the cutting line to the optimum
length. This is covered by a guard (Fig. 7a/Item F).
Remove the guard before you start working and
replace it when you have fi nished working.
5.2.4 Fitting/Replacing the line spool
The fi tting of the line spool is shown in Figure 7c-
7d. To dismantle, proceed in reverse order.
Look for the hole in the carrier plate, line up with
the notch beneath it, lock with the supplied hexa-
gon key (29), and screw the line spool onto the
thread. Note: Left-hand thread
15.03.2019 07:39:35 15.03.2019 07:39:35