Multizone - Franke FDW 614 D7P DOS A++ Mode D'emploi

OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times and beeps
will sound. The option will not be enabled.
DELAY
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
1.Press the DELAY button: the corresponding symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2.Select the wash program and close the door: the timer
will begin counting down;
3.Once this time has elapsed, the indicator light switches
off and the wash cycle begins.
To adjust the delay time and select a shorter period of
time, press the DELAY button. To cancel it, press the
button repeatedly until the selected delayed start
indicator light switches off.
The wash program will start automatically as soon as the
door is shut.
The Delay function cannot be set once a wash cycle
has been started.

MULTIZONE

If there are not many dishes to be washed, a half loading
may be used in order to save water, electricity and
detergent.
Select the program and then press the MULTIZONE
button: the symbol of the chosen rack will appear on the
display. By default the appliance washes dishes in all
racks.
To wash only the specific rack, press this button
repeatedly:
shown on the display (only lower rack)
shown on the display (only upper rack)
shown on the display (only cutlery rack)
shown on the display (option is OFF and the appliance will
wash dishes in all racks).
Remember to load the upper or lower rack only, and to
reduce the amount of detergent accordingly.
6
17-Apr-2019 09:30:12 EDT | RELEASED
Note: If CoolDry is active and it opens the door, then Operation
Indicator will not flash at the end of cycle.
CoolDry
CoolDry is a convection drying system which automatically opens the
door during/after drying phase to ensure exceptional drying
performance every day. Door opens at the temperature that is safe to
your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher. To see how to mount protection
foil please refer to (INSTALLATION GUIDE).
CoolDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding P button
(6 sec).
2. You are currently in Light Control Menu (please refer to OPERATION
INDICATOR description), if you don't want to change anything
please press and hold P button (until one of the two letters appears
on the display).
3. You switched to CoolDry Control Menu, you could change status of
CoolDry functionality by pressing P button:
E
– enabled
To confirm the change and exit from the Control Menu please press
and hold P button (3 sec).
In some European factories the letter "W" of the part code mentioned herein will be automatically
replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")
TABLET (Tab)
This setting allows you to optimize the performance of
the program according to the type of detergent used.
Press the TABLET button (the indicator light will light up)
if you use combined detergents in tablet form (rinse aid,
salt and detergent in 1 dose).
If you use powder or liquid detergent, this option
should be switched off.
OPERATION INDICATOR
An amber LED light on the floor indicates that the
dishwasher is working. One of the following operating
modes can be selected:
a) Disabled function.
b) When the cycle starts the light goes on for few seconds,
stays off during the cycle and flashes at the end of the
cycle.
c) The light stays on during the cycle and flashes at the
end of the cycle (default mode).
If the delayed start was set, the light goes on either for the
first few seconds or the entire duration of the countdown,
based on whether mode b) or c) was set.
The light goes off every time the door is opened. To select
the mode you prefer, switch on the machine, hold down
button P until one of the three letters appears on the
display, press button P until you reach the desired letter
(or mode), hold down button P to confirm the selection.
d
– disabled