Pre-Start Up Procedure; Operation Of Your Ecosalt2; Control Panel; Initial Start-Up - Davey EcoSalt 2 DES2-15E Instructions D'installation Et D'utilisation

PRE-START UP PROCEDURE

Before operating your EcoSalt2 salt pool chlorination system, please ensure the following quantity of pool
salt has been added to your pool.
• POOL SALT:
To raise salt
concentration by
50,000L
30,000L 40,000L
ppm (7,925 gal) (10,567 gal) (15,850 gal)
(13,208 gal)
%
(mg/L)
kg lbs kg lbs kg lbs
1,000 0.1 30 66 40 88 50 110 60
2,000 0.2 60 132 80 176 100 220 120 265 140 309 160
3,000 0.3 90 198 120 265 150 331 180 397 210 463 240
4,000 0.4 120 265 160 353 200 441 240 529 280 617 320
5,000 0.5 150 331 200 441 250 551 300 661 350 772 400
6,000 0.6 180 397 240 529 300 661 360 794 420 926 480 1,058 540 1,190 600 1,323
• CHLORINE: For a new pool installation that has not been chlorinated, add sufficient Chlorine (liquid or
granular) to achieve a reading of 3ppm (mg/L) with a suitable test kit. Alternatively, run the EcoSalt2 salt pool
chlorination system continuously on BOOST MODE, for approximately 24 hours, or until a reading of 3ppm
(mg/L) is reached.
• STABILISER: It is essential that pool stabiliser be added and maintained at the rate of 25-50ppm (mg/L)
at all times (FOR OUTDOOR POOLS ONLY). For ORP controlled systems the stabiliser level should be
maintained between 15-25ppm (mg/L).
• (Refer Day to Day Operation page 27 for further information).

OPERATION OF YOUR EcoSalt2

CHLORINE OUTPUT is expressed as a percentage. Set the EcoSalt2 to the percentage output required
and the unit will automatically adjust the cell output to the set level. The EcoSalt2 is fitted with an electronic
control and warning system. This regulates the output of the EcoSalt2 to the pre-set maximum and changes
cell polarity as indicated by the + or – on the digital display. The polarity will alternate over a number of hours
of chlorination time, not necessarily pump-run hours.
Salt required
60,000L 70,000L
80,000L 90,000L 100,000L
(23,775 gal) (26,417 gal)
(18,492 gal) (21,134 gal)
kg lbs kg lbs kg lbs kg lbs kg
132 70 154 80 176 90 198 100
353 180 397 200
529 270 595 300
705 360 794 400
882 450 992 500 1,102
8

CONTROL PANEL

LAYOUT
lbs
220
441
661
882
Manual on/off
Depending on software of your EcoSalt2, this
button may be disabled. In that case you will
need to decrease the production to 0% to
turn off the chlorine production
Menu up/down
Menu/setting select
Menu/setting cancel (go back)

INITIAL START-UP

Once the salt level in the pool is correct the unit may be switched on.
Note: Once the unit starts there is a short time delay until the cell operates to ensure the filtration
system is primed with water.
• The first time the EcoSalt2 is turned on, the following screen is shown on start-up:
> This screen shows the version of software (ie v1.2.1 shown) and your model of EcoSalt2 (ie EU 15L
shown, meaning DES2-15EL).
• The display then automatically reverts to the following screen:
100% – 09:29 AM
ON
Power indicator
(lit when EcoSalt2 on)
Alarm indicator
(flashes when alarm active)
Time out
(whenever device is left for 30 seconds
without input from user, settings are saved,
and home screen displayed)
DAVEY
V1.2.1 EU 15L
9