Cleaning And Maintenance; Technical Characteristics - TZS First AUSTRIA FA-5571-4 Manuel D'utilisation

INSTRUCTION MANUAL
WALL MOUNTED PTC FAN HEATER USAGE GUIDANCE
• Please read this guidance carefully before using your wall mounted PTC heater, so that you
can use it correctly.
• Please keep well with this guidance.
BRIEF INTRODUCTION OF THE PRODUCT
PTC heater has a heating and fan function in the same machine, and it looks like an air
conditioner with latest design. With remote control make it to be operated easily and safely, the
machine adopts PTC heating material heating it quickly, it's durable and without flame.
FEATURE:
1. High quality plastic shell and long using life.
2. PTC ceramic heater elements, high efficiency heating, quickly heating, noiseless, odor-
free, non-polluting, non flamable and will not killing the oxygen.
3. Two level heat setting, you can arrange the temperature as your prefer.
4. There is a temperature fuse to prevent overheating and motor overheat protection. It
automatically turns off when the wind outlet is blocked and turns on again when the
sundries are cleared away.
5. Automatic oscillating blinds and wide angle oscillating.
6. Remote control function, 7.5 hours timer. Natural/cool/hot wind for selection.
7. Safety thermostat. Overheat protection.
NOTES:
1. The heater should be hung on the wall and the wind outlet should face down or be placed
on flat appliance. You must not place it precipitantly or tipsily.
2. Please do not use the heater in places full of combustible or explosive gas. Don't cover the
wind outlet.
3. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent
or a similarly qualified person in order to avoid a hazard
4. The heater must not be located immediately below a fixed electric outlet. The electric outlet
must be equipped with installment of earth the capacity of which should be 240V-10A or
exceed 240V-10A. Make sure the socket and plug contact well.
5. If nobody is in or you are repairing the heater, please disconnect the heater from electric outlet.
6. Please don't touch the heater with wet hands or other conductors.
7. Motor is out of order, please make it stop immediately.
8. During use, please do not open the door or window otherwise it will diminish the heating
effect.
9. To turn off the machine, press the on/off switch to off, then the machine will keep the fan
working about 30 seconds until it blows out cool wind, then the machine will stop working
and you can take out the plug.
10. Must hang the heater on the wall and fix it away from water in bathroom.
11. Remote control, please use 2 AAA battery, matched with the heater, heater panel LED
display room temperature.
If the product needs repair, please ask experts or our company authorized maintenance
department.
WARNING:
Don't touch the working machine and don't cover the wind outlet and inlet!
NAME OF THE COMPONENTS
(see picture 1):
1) COVER 3) WIND OUTLET
2) WIND INLET 4) FANNER
M_5571-4_v03.indd 2-3 M_5571-4_v03.indd 2-3
5) BASE
6) CONTROL PANEL
2
INSTALLATION
(see picture 2):
Drill two holes into the wall and keep a distance of 1.8m from the ground. The diameter of the
hole just contains the inflated plastic pipe. After tucking the inflated plastic pipe, fix pothook on
the pipe with screws. Make sure pothook are safely placed and hang the heater. The clip under
the pothook should be inserted rabbet of the heater bottom.

CLEANING AND MAINTENANCE

1. If you don't use the heater for a long time, please wipe the surface and put it into the box.
Lay the carton on a ventilated and dry place. Humidity and pressure on the carton can
damage your product.
2. Wait for the machine to cool down before pulling out the plug, then clean it. Wipe it clean
with a wet washcloth or cleaner. Never directly wash with water, do not drop water into the
machine. Never clean with acids, chemical thinner, gasoline, benzene etc.
3. Before every use, please check to make sure that the outlet ventilation has no sundries.
REMOTE CONTROL INSTRUCTION
(see picture 3):
OPERATION STEPS
1. ON/OFF button: Press the button to turn on, the pilot lamp will go on and cold wind will
start blowing out. Press again to turn off power.
2. FUNCTION button: You can select 2 levels of power through this button.
Power 1 is 1000W
Power 2 is 2000W
3. SWING button: press the button to auto-swing, press it once more to stop.
4. TIMER button: press the button to set the heater working hours, 7.5 hours at most, shown
by indicating light.
USAGE
1. There are eight indicator lights and two buttons on the control panel, above buttons control
on/off, cool air, 1000W/2000W, swing; below buttons control timer.
2. To turn off the machine, press the on/off switch to off, then the machine will keep the fan
working for another 30 seconds until it blows out cool wind, then the machine will stop
working and you can unplug the machine.
3. Please make sure that the electrical-outlet is equipped with installment of earth the capacity
of which should amount to 240V-10A or exceed 240V-10A. Make sure the socket and plug
contact well.
4. Timer sets the heater working hours. Half an hour, one hour, two hours and four hours
progression time.
ELECTRIC DRAWING
(see picture 4)
1. AC 220V
2. Thermostat
3. PTC Ceramic
4. Control Panel
5. Execution Panel
6. Overheat protection
7. Main motor
8. Oscillation motor

TECHNICAL CHARACTERISTICS

220-240V • 50Hz • 2000W
3
2010.5.18 3:33:47 PM 2010.5.18 3:33:47 PM