Publicité
Les langues disponibles
Les langues disponibles
Machine setting
1.
Ensure that the Battery connector (25, Fig. C) is
completely disconnected.
2.
Remove the key (24, Fig. C) from its housing and
remove the tank assembly fastening screw (1, Fig.
H).
3.
Carefully lift the tank assembly (19, Fig. H) by
means of the manoeuver handle (2, Fig. C).
4.
The machine setting performed at the factory is for
lead (WET) batteries. If the setting corresponds to
the chosen battery, go to step 8, otherwise
perform the operations at points 5, 6, 7.
5.
Unscrew the screws (4, Fig. G) and carefully
remove the electric component box cover (5)
making it slide upwards.
6.
Move the micro-switch (6, Fig. G) upwards
(dip-switch) to GEL position.
WARNING!
Do not move the adjacent switch (7, Fig.
G).
7.
Reinstall the electric component box cover (5, Fig.
G) and screw the screws (4).
Battery charger setting
8.
Take the battery charger selector (18, Fig. H) to
WET position for lead battery, or to GEL position
for gel battery.
Battery installation and charge
9.
Install the batteries on the machine according to
the diagram (15, Fig. H).
10. Proceed with recharging the batteries (see the
procedure in the paragraph "Maintenance").
NOTE:
Battery charger must be connected to the
batteries for machine to function.
BEFORE MACHINE START-UP
Brush or pad-holder installation
REMARK:
Depending on the type of floor, either a
brush (24, Fig. H) or a pad-holder (25)
with pad (26) can be installed.
To simplify, the following instructions
refer to the brush only.
1.
Lift the brush-holder (9, Fig. C) by means of the
pedal (20, Fig. C).
08812946(3)2003-08
INSTRUCTION MANUAL FOR USE AND MAINTENANCE
2.
Position the brush (24, Fig. H) under the
brush-holder.
3.
Lower the brush-holder (9, Fig. C) by means of the
pedal (20, Fig. C).
4.
(20BT versions only): Turn the key (9, Fig. B) to "I"
5.
Press the brush push-button for a few seconds (5,
Fig. B) to hook the brush/pad-holder.
Squeegee installation
6.
Install the squeegee into place (10, Fig. C) and fix
the handwheels (11), then connect the hose (26)
to the squeegee.
7.
Adjust the squeegee by means of the handwheel
(12, Fig. C) so that its rear blade (14, Fig. C) - in
all its length - touches the floor and that the front
blade (13) is slightly detached from the floor.
Adjustments
8.
Adjust the handlebar (2, Fig. C) by means of the
handles (3), to reach a comfortable position.
Detergent tank filling up
9.
Open the cover (2, Fig. H) of the tanks.
10. Fill the detergent tank (6, Fig. H) with an appro-
priate detergent, depending on the cleaning to be
carried out.
It is possible to check the tank filling up by means
of the marks (27, Fig. C).
Do not fill the detergent tank completely and let
the detergent level a few centimeters from the rim.
Always follow the dilution instructions on container
label of the chemical product used to create the
detergent solution.
The detergent temperature must be under 40°C
(100°F).
MACHINE START-UP AND STOP
Machine start-up
1.
Prepare the machine as described in the previous
paragraph.
2.
Lower the squeegee (10, Fig. C) by means of the
lever (19).
3.
Lower the brush (8, Fig. C) by means of the pedal
(20).
CAUTION!
Use only low-foam and non-flammable
detergent liquids, appropriate to the
use.
9
Publicité
Chapitres
