Krups EA829 Mode D'emploi page 10

Cappuccino system rinsing
You can rinse the system after preparing a cappuccino. This is even possible if there is still milk in the milk jug. It is important to
carry out this rinsing cycle after each cappuccino prepared.
The milk jug must be in place as described in the paragraph PREPARING A CAPPUCCINO.
Turn the cappuccino system's lid button to the position CLEAN (30).
While the screen is displaying the drinks selection menu, press the machine's CLEAN button (31). Simply follow the on-screen
prompts to start the rinsing cycle. At the end of the cycle, turn the cappuccino system button to the CAPPUCCINO position before
preparing a new recipe.
IMPORTANT:
It is recommended that you carry out this rinsing operation before returning the milk jug (if it still contains milk) to the
refrigerator following preparation of the last cappuccino. After each rinsing operation, it is recommended that you clean the
different pieces of the system under running tap water (see paragraph Manual maintenance of milk jug).
Coffee circuit cleaning program - total duration: around 20 minutes
You should run the cleaning program at the end of around 360 preparations of espresso or coffee.
The appliance will warn you by periodically displaying a message when it is time to carry out cleaning.
To carry out a cleaning program, you will require a container with a capacity of at least 20 oz and a KRUPS XS 3000 cleaning
tablet (32a).
If you unplug your machine during the cleaning cycle, or if there is a power failure, the cleaning program will continue from
the current phase when the power is returned. It will not be possible to cancel this operation.
This is essential to ensure that the water circuit has been correctly rinsed. In this case, a new cleaning tablet may be
necessary. Ensure that the cleaning program has been completed to avoid any risk of poisoning.
The cleaning cycle is an intermittent cycle. Do not put your hands beneath the coffee outlets during the cycle.
When the message "Cleaning necessary" is displayed, you can start the automatic cleaning program by pressing the PROG
button.
Carefully follow the instructions given on screen.
The automatic cleaning program is divided into three parts: the cleaning cycle itself, then two rinsing cycles. This program
takes approximately 20 minutes. You can start cleaning at any time by pressing PROG to display the menus then select
MAINTENANCE OK COFFEE CLEANING.
Only use KRUPS cleaning tablets (XS 3000) (32a). We are not responsible for any damage caused by the use of tablets of other
brands.
You can obtain cleaning tablets from the KRUPS After-Sales Service.
Descaling program - duration: around 22 minutes
If your product is equipped with our Claris - Aqua Filter System F088 cartridge, please remove this cartridge before
the descaling operation.
The amount of limescale collected depends on the hardness of the water used. The appliance will warn you by periodically
display a message when it is time to carry out descaling.
To carry out a descaling program, you will need a container with a capacity of at least 20 oz and a KRUPS F054 (40 g) descaling
pouch (32b).
When the message "Descaling necessary" is displayed, you can start the automatic descaling program by pressing the PROG
button.
Carefully follow the instructions given on the screen, ensuring that the contents of the pouch have dissolved.
The descaling cycle is divided into three parts: the descaling cycle itself, followed by two rinsing cycles.
Use only KRUPS descaling products. Descaling products are available from KRUPS After-Sales Service centers.
We are not responsible for any damage caused to the appliance by the use of other products.
If the appliance is dropped while not in its packaging, it is recommended that you take it to an approved repair centre to
avoid any risk of fire or electrical problems.
If a power failure takes place or if you unplug your machine, the cycle will continue from the current phase when the power is
returned. It will not be possible to cancel this operation.
Ensure that the descaling program has been completed to avoid any risk of poisoning. The descaling cycle is an intermittent
cycle. Do not put your hands beneath the steam nozzle during the cycle.
Ensure that you protect your worktop during the descaling cycles, particularly if it is made of marble, stone or wood.
8