Page 1
BEAM1R-MKII CODE: 15-1937 DMX MOVING HEAD 1R 100W WITH OSRAM SIRIUS HRI LAMP LYRE 1R DMX 100W AVEC LAMPE OSRAM SIRIUS HRI DMX MOVING HEAD 1R 100W MIT OSRAM SIRIUS HRI LAMPE GB - User Manual - p. 2 F - Manuel d'Utilisation - p. 13 D - Bedienungsanleitung - S.
10 minutes. The lamps are not covered by the warranty. Thank you! SAFETY RECOMMENDATIONS Thank you for having chosen our AFX LIGHT MOVING HEAD WITH DMX CONTROL. For your own safety, please read this user manual carefully before installing the device.
must be more than 10cm. Keep a distance to any flammable objects of at least 12m. • Operate the device only after having familiarized yourself with its functions. Do not permit ope- ration by person not qualified for operating the device. Most damages are the result of unprofes- sional operation. • Please use the original packaging if the device is to be transported. • For safety reasons, please be aware that all modifications on the device are forbidden. Further- more, any other operation may lead to short-circuit, burns, electric shock, lamp explosion, crash, etc.
Page 4
O U T O U T O U T The connection between the output of master and input of product, it’s available to use the 3 pins XLR cable which provided by the manufacturer. Signal cable from the DMX output of the controller to the input of the first master light, and connect to the DMX input of second slave light from the DMX output of the first master light, analogously, till connected all the slave lights, and insert the last connector to the output of the final light. (Notice: the diameter of core of every cable should...
OPERATION 2.1 Press “MODE” to switch the menu • SET setup o Run mode : Choose operating mode ( AUTO / SOUND / DMX / SLAVE ) o DMX address : Set DMX address o Channel mode o Lamp control o Sound sensitive o X reverse o Y reverse o X/Y exchange o No DMX signal o Screen protect o Open the lamp o Restore to default settings...
X Reverse Y Reverse X/Y Exchange Change the channel of X/Y axis (include X/Y Fine) No DMX Signal KEEP According to the original state continues to run CLEAR Motor reset, stop running Display screen Closing backlight after free 30seconds protect Backlight still lighting Lamp on start up Reset directly after Power on, lamp off (need to use the menu or control table to manual let lamp light) Lamp light directly after power on, And must wait for the lamp light up success then reset...
Page 7
This time lighting hour This time lighting hour (accurate to minute) Error information Instruction Reset fail, uart error Driver board doesn’t respond. There is problem in the uart commu- nication line of display board and driver board. Or the driver board problem. Pan reset fail X photoelectric switch, or X Motor problem Tilt reset fail Y photoelectric switch, or Y Motor problem Pan Hall error...
Page 8
3. DMX CHANNELS Channel Value Function 0---255 0---255 PAN FINE 0---255 TILT 0---255 TILT FINE 0---255 PAN-TILT Speed 0---4 color1 5---9 color1+color2 10---14 color2 15---19 color2+color3 20---24 color3 25---29 color3+color4 30---34 color4 35---39 color4+color5 40--44 color5 45---49 color5+color6 50---54 color6 55---59 color6+color7 60---64...
Page 9
40--44 gobo9 45---49 gobo10 50---54 gobo11 55---59 gobo12 60---64 gobo13 65---69 gobo14 70--139 Gobo wheel shake from slow to fast. Every 5 values a gobo 140--200 Gobo wheel forward rotation from fast to slow 201--205 Stop 206--255 Gobo wheel reverse rotation from slow to fast 0---127 PRISM 128---255...
Page 10
YELLOW + BROWN YELLOW YELLOW GREEN + YELLOW YELLOW GREEN PURPLE RED + YELLOW GREEN PURPLE RED BLUE + PURPLE RED BLUE DARK YELLOW + BLUE DARK YELLOW ROSE RED +DARK YELLOW ROSE RED GREEN + ROSE RED GREEN LIGHT YELLOW + GREEN LIGHT YELLOW RED + LIGHT YELLOW WHITE + RED...
Page 11
GOBO 2 GOBO 1 WHITE 3.3 PRISM INSERTION - CHANNEL 8 EFFECT 128-255 PRISM INSERTED 0-127 PRISM EXCLUDED 3.4 PRISM ROTATION - CHANNEL 9 EFFECT FAST ROTATION …… …… SLOW ROTATION SLOW ROTATION …… …… FAST ROTATION 0-127 POSITION 3.5 PAN - CHANNEL 1 3.6 PAN FINE - CHANNEL 2 3.7 TILT - CHANNEL 3 3.8 TILT FINE - CHANNEL 4...
Page 12
CLEANING AND USING FREQUENCY OF PRODUCT Please make sure that the light is power off before dismantling or maintaining, it’s very important to keep the light clean. Frequent cleaning will ensure maximum brightness output, but also prolong the life time. It’s suggested to use the high quality, professional glass detergent and soft cloth to clean the light.
NOTICE D'UTILISATION Nous vous remercions pour l’achat de cette LYRE DMX AFX LIGHT. Pour votre sécurité, lisez atten- tivement ce manuel avant d’installer l’appareil. CONSIGNES DE SECURITE ET D’UTILISATION • Si l’appareil a été exposé à des changements de température, ne le mettez pas immédiatement sous tension.
• Utilisez cet appareil uniquement si vous vous êtes familiarisés avec ses fonctions. Ne pas autori- ser une personne inexpérimentée d’utiliser cet appareil. La plupart des dommages résultent d’une mauvaise utilisation. • Conservez l’emballage d’origine pour tout transport. • Pour des raisons de sécurité, il est interdit de modifier cet appareil de quelque sorte que ce soit. Toute manipulation non décrite dans ce manuel peut conduire à...
O U T O U T O U T Note: Utilisez du câble à double blindage. Le diamètre du conducteur de chaque câble doit être d’au moins 0,5mm. BRANCHEMENT DU CORDON D’ALIMENTATION Utilisez le cordon fourni pour brancher l’appareil sur le secteur. Vérifiez que votre tension secteur correspond bien à la tension d’alimentation de l’appareil qui est de 90-245V~ 50/60Hz. L’effet pos- sède un interrupteur d’alimentation indépendant.
UTILISATION 8.8.8.8. MENU DOWN ENTER Mode Func. DOWN Appuyez sur “MODE” pour sélectionner les différents menus • MENU SET UP o Run mode : Pour choisir le mode de fonctionnement ( AUTO / SOUND / DMX / SLAVE ) o DMX address : Pour ajuster l’adresse DMX de la lyre o Channel mode o Contrôle de la lampe o Sensibilité audio o Inversion X o Inversion Y o Echange X/Y o Absence de signal DMX o Protection écran...
Page 17
1-512 Appuyez sur ENTER pour aller en mode Edition. Sé- lectionnez le chiffre des centaines et appuyez sur UP/ DOWN pour changer l’adresse. Appuyez sur ENTER, sé- lectionnez le chiffre des dizaines et changez le chiffre DMX Address avec les touches UP/DOWN. Appuyez sur ENTER, sé- lectionnez le chiffre des unités et changez le chiffre avec les touches UP/DOWN.
Informations d’erreur Instruction Reset fail, uart error La platine du moteur ne répond pas. Il y a un problème dans la commu- nication UART entre la platine du moteur et la platine de l’afficheur. Pan reset fail Problème avec le commutateur photoélectrique X ou avec le moteur Y Tilt reset fail Problème avec le commutateur photoélectrique Y ou avec le moteur X Pan Hall error Problème avec le Hall X...
Page 20
0---4 gobo1 5---9 gobo2 10---14 gobo3 15---19 gobo4 20---24 gobo5 25---29 gobo6 30---34 gobo7 35---39 gobo8 40--44 gobo9 45---49 gobo10 50---54 gobo11 55---59 gobo12 60---64 gobo13 65---69 gobo14 70--139 Gobo wheel shake lent -> rapide. Un gobo toutes les 5 valeurs 140--200 Rotation vers la droite de la roue de gobo: rapide ->...
Page 21
3.1 ROUE DE COULEUR – CANAL 6 EFFECT FAST - SLOW ROTATION …… …… SLOW - FAST ROTATION CTO 8000 + WHITE CTO 8000 FLUORESCENCE + CTO 8000 FLUORESCENCE BROWN + FLUORESCENCE BROWN YELLOW + BROWN YELLOW YELLOW GREEN + YELLOW YELLOW GREEN PURPLE RED + YELLOW GREEN PURPLE RED...
Page 22
3.2 CHANGEMENT DU GOBO STATIQUE - CANAL 7 EFFECT FAST REVERSE ROTATION SLOW ROTATION STOP FAST - SLOW FORWARD ROTATION GOBO 13 SHAKE SLOW TO FAST …… …… GOBO 3 SHAKE SLOW TO FAST GOBO 2 SHAKE SLOW TO FAST GOBO 1 SHAKE SLOW TO FAST GOBO 13 GOBO 12...
3.5 PAN - canal 1 3.6 PAN FINE - canal 2 3.7 TILT - canal 3 3.8 TILT FINE - canal 4 3.9 LAMP CONTROL & RESET - canal 12 EFFECT Remark 200-255 COMPLETE RESET 150-199 PAN/TILT RESET Reset is activated passing through the unused range and staying 5 seconds.
BEDIENUNGSANLEITUNG Bitte lesen Sie diese Anleitung sorgfältig durch, bevor Sie das Gerät in Betrieb nehmen. VORSICHT: Lampen nicht beschädigen! Gerät ausschalten und mindestens 10 Minuten abkühlen lassen, bevor Sie es berühren. Die Lampen sind vom Garantieanspruch ausgeschlossen. SICHERHEITSVORSCHRIFTEN • Diese Anleitung sorgfältig vor der ersten Inbetriebnahme lesen. Sie enthält wichtige Informa- tionen über Installation, Gebrauch und Instandhaltung des Geräts.
Page 25
4. Das Gerät enthält keine Ersatzteile zur Reparatur. Überprüfen Sie vor dem Betrieb, ob alle Teile gut installiert und die Schrauben fest angezogen sind. Verwenden Sie das Gerät nicht, wenn das Gehäuse geöffnet ist. RIGGING • Das Gerät kann in jeder beliebigen Stellung montiert werden, sofern ausreichend Platz für Belüf- tung vorhanden ist •...
Page 27
Letzte Betriebsdauer des Leuchtmittels • ADVANCED setup o Sensormonitor o Reset Kalibrierung o Lebensdauer des Leuchtmittels o Betriebsdauer löschen • Wechseln zwischen Chinesisch – Englisch • Display umkehren 2.2 Konfigurieren der Schnittstelle Option Anweisung Slave: Akzeptieren der Signale vom Master Auto1 Master: Automatikbetrieb und Senden von DMX Signalen an den Slave...
2.3. Manuelle Einstellungen Das Gerät kann manuelle gesteuert werden, wenn kein DMX Signal vorhanden ist. Option Anweisung 1CH. X 0~255 OK drücken. 100er Stelle wählen. Mit den UP/DOWN Tasten die Adresse einstellen. OK drücken. 10er Stelle wählen und editieren. OK ……...
Page 29
Gerät bedient. Das Standardpasswort lautet "UP DOWN UP DOWN". Drücken Sie die EINGABE- TASTE, um das Kennwort zu überprüfen. Option Anweisung Zustand des Hall-Sensors 0 = Magnet schliesst, 1 = Magnet aktiv Zustand des Hall-Sensors 0 = Magnet schliesst, 1 = Magnet aktiv des Farbrads Zustand des Hall-Sensors 0 = Magnet schliesst, 1 = Magnet aktiv...
Page 32
ROT + GELB YELLOW WEISS + ROT WEISS 3.2 WECHSEL STATISCHER GOBOS - KANAL 7 EFFECT FAST REVERSE ROTATION SLOW ROTATION STOP FAST - SLOW FORWARD ROTATION GOBO 13 SHAKE SLOW TO FAST …… …… GOBO 3 SHAKE SLOW TO FAST GOBO 2 SHAKE SLOW TO FAST GOBO 1 SHAKE SLOW TO FAST GOBO 13...
Page 33
…… …… SCHNELLE DREHUNG 0-127 POSITION 3.5 PAN - KANAL 1 3.6 PAN FEINEINSTELLUNG - KANAL 2 3.7 TILT - KANAL 3 3.8 TILT FEINEINSTELLUNG - KANAL 4 3.9 LEUCHTMITTELSTEUERUNG & RESET - KANAL 12 EFFECT Bemerkung 200-255 KOMPLETTES RESET Reset ist aktiviert, läuft durch den unbelegten Bereich und dauert 5 Sekunden 150-199...