LEMAN LOSAE250 Manuel D'utilisation page 19

GB
SPECIAL REQUIREMENTS FOR LEAF BLOWER/VACUUM
- Never start the unit and never leave it running in a closed room or building. Use the unit outdoors only.
- Wear eye and ear protection when using the unit. If working in a dusty environment, wear a face or dust mask. A
long-sleeved shirt is recommended.
- Wear thick, long trousers, boots and gloves.
- Keep hair, clothing and gloves away from moving parts. Loose clothing, jewellery or long hair may become
caught by moving parts. If required, wear a hair net.
- Use this unit for its designated purpose only.
- Do not stretch too far over the unit. Always have a secure footing and keep your balance.
- Do not use this unit unless it is fully assembled. Do not use the unit without attached vacuum/blow pipe and
vacuum bag. Check that the vacuum bag is closed.
- Never carry the unit by the power cord.
- Always guide the unit power cord away from the unit to the rear.
- Before carrying out any care and maintenance work or installingand removing the blow/vacuum pipe and vacuum
bag, switch off the motor and pull the mains plug out of the socket.
- Operate the unit in daylight or adequate artificial lighting only.
- Avoid starting the unit unintentionally. Be ready to operate the unit as soon as you switch it on. User and unit
must be in a stable position when the unit is started. Follow the instructions for starting and stopping the engine.
- If the unit hits or becomes ensnared by a foreign object, immediately switch off the engine and check for damage.
Before checking the unit, pull the mains plug out of the socket.
- Never use the unit with loose or damaged parts.
- While the engine is running, never place the unit on dusty or dirty surfaces. Dirt, grass, foliage, etc. may be drawn
in and cause injuries and/or damage the unit.
- If there are any unusual vibrations, immediately switch the motor off and pull the mains plug out of the socket.
Check the unit for damage. If the unit is damaged, contact a specialist company.
- Switch the motor off and pull the mains plug out of the socket before removing obstructions/ blockages, emptying
the collection bag or before carrying out any work on the unit, e.g. checking, cleaning, transporting, adjustments.
- Keep hands, face and feet away from all rotating parts. Do not touch the rotor while it is rotating and do not try to
stop it either.
- Never use this unit to spread chemical products, fertilisers or other substances which contain toxic substances.
- Do not put anything into the intake opening by hand.
- Do not use the unit in adverse weather conditions, e.g. if there is a probability of rain or a storm.
- Keep away from naked flames, avoid creating sparks and do not smoke.
- When using the unit as a blower, never point the unit at persons, pets or windows. Always blow in a direction in
which there are no persons, animals or fragile, solid surfaces (e.g. windows, walls, cars).
- Do not attempt to draw in damp objects or water, as the unit may be damaged.
- Do not vacuum up metal, pieces of glass, etc., as the rotor could be severely damaged as a result.
- Do not draw in hot objects, such as ash, embers, cigarettes, etc. The vacuum bag could catch fire.
- Before starting work, clear the working area of all foreign objects which may damage the unit or which may cause
injuries or damage if blown away or ejected.
- Before storing or transporting the unit, leave the engine to cool down.
- Protect your unit while it is being transported.
- Store the unit in a dry, closed room to prevent unauthorised use or damage. Keep the unit away from children.
- Never douse or splash the unit with water or other liquids. Keep the unit dry, clean and free of dust. Clean the unit
after each use and follow the instructions for cleaning and storage.
- Observe the national/municipal regulations concerning times of use (if required, ask your local authority).
ASSEMBLY
Prior to assembly and adjustment, always unplug the machine.
Check for damage to the machine, parts or accessories which may have occurred during transportation.
1. Mounting the pipes (Fig 3 to 6)
- Push the lower pipe (12) into the upper pipe (13) (Fig 3 & 4).
- Screw one screw M4x50 (14) in and tighten (Fig 5).
- Push the upper pipe (13) into the main unit (Fig 6).
- Screw the second screw M4x50 (14) in and tighten.
19