Sanisan Condens Notice D'installation page 6

EN
1
CAUTION
SANISAN ® CONDENS is a pump for lifting condensation
water from an air conditioning system, a condensation boiler
or from refrigeration units. Include a neutralisation device if
necessary (see the manufacturer's instructions for your
boiler).
The pump starts automatically and has a high level of
performance, safety and reliability provided that all the
installation and maintenance instructions described in this
notice are strictly followed.
Please take particular note of the information marked by :
" " Failure to comply with this instruction could endanger
the safety of persons,
" " Indication that a risk of electrical origin exists,
" " Instructions for use only by qualified professionals,
"CAUTION" Failure to comply with this instruction could
endanger the safe function of the apparatus
Please contact our Customer Services for any additional
information.
OPERATING PRINCIPLE
®
SANISAN CONDENS contains 1 pump. The tank of the
SANISAN ® CONDENS is fitted with a float which controls the
operation of the motor. When the condensates enter the tank,
the pump starts up.
2
LIST OF DOCUMENTS PROVIDED
3
DIMENSIONS
4
SANISAN ® CONDENS AREA OF APPLICATION AND
TECHNICAL DATA
Air conditioning systems, boilers,
Application
Type
Max. vertical pumping
Maximum flow rate (litres / hour)
Min. pH
Voltage
Frequency
Power rating
Current consumption
Electrical class
Protection index
Sound level
Average utilisation temperature
Maximum allowable temperature
S3 15% (90s ON, 510s OFF)
Net weight
Dimensions
Tank volume
Supply cable
Discharge hose
Alarm cable (3 core)
Wall fastening
CAUTION :
All applications other than those described in this notice are
prohibited.
5
PERFORMANCE CURVES
6
VERTICAL PUMPING/HORIZONTAL PUMPING
refrigeration units
CD10
4,5 m
342
2,5
220-240 V
50 Hz
60 W
0,52 A
I
IP20
<45 dBA
35°
80°
2000 g
283x160x127
1,2 litre
2 m
6 m
2 m
Yes
7
INSTALLATION
SANISAN ® CONDENS has wall fixings.
The unit should be easy to access for testing and
maintenance.
The unit must be installed level. Adjust the installation using a
spirit level before fixing the unit.
Make sure that the equipment is protected from damp while
installing it.
7a
CONNECTION AT THE COVER INLET
To connect the water to be drained, connect the water inlet to
®
the SANISAN CONDENS inlet
7b
CONNECTING TO THE DISCHARGE PIPE
The SANISAN ® CONDENS discharge pipe must be
connected to the flexible hose
This hose should be used to form the vertical section of the
discharge pipe.
• Place the flexible hose onto the non-return valve of the
SANISAN ® CONDENS .
• Position the flexible hose in the most vertical position
possible to avoid it kinking.
• It is advisable to make a circular bend to avoid the hose
kinking.
• The hose has a diameter of less than 8 mm and can be
connected to a PVC hose of larger diameter by a plastic
reducing connection on the horizontal section of the
discharge hose, or connected to your drain by a plastic
reducing connection (not supplied).
The SANISAN ® CONDENS is fitted with a non-return valve
to prevent start up at an inappropriate time.
INSTRUCTIONS INTENDED SOLELY FOR
QUALIFIED PROFESSIONALS
7c
ELECTRICAL CONNECTION
The electrical installation should be carried by a qualified person.
All wiring must conform to BS7671, 1992 requirements for
electrical installations. The SANISAN
220/240V single phase AC 50 Hz supply (UK specification).
®
Do not connect SANISAN
and socket. It must be wired into a fused, unswitched, fixed
wiring connector fitted with a 5 amp fuse. SANISAN
CONDENS has an Earth wire. The wires in the mains lead
are coloured in accordance with the following code:
Brown – Live Blue – Neutral
Warning: Ensure the electricity is turned OFF at the main
switch board before wiring to connector.
All work on cable, pressure chamber and motor should only
be carried out by a qualified Saniflo servicing agent, as
special tools are required.
INSTRUCTIONS INTENDED SOLELY FOR
QUALIFIED PROFESSIONALS
7d
ALARM
SANISAN ® CONDENS is fitted with a detection system that
can trigger an alarm if the water level rises too high
(audible or visual alarm, 1.5V to 230V), see diagram
B
. Brown wire: shared wire
C
. Black wire: normally off
D
. Blue wire: normally on
To fit the alarm, connect the blue and brown wires
of the alarm to the respective terminals on the
®
SANISAN CONDENS
OPTIONAL: if you connect the brown and black wires to the
control relays on your boiler, it will be switched off if the water
level rises too high in the unit.
ATTENTION: The maximum current admissible for our
detection system is 0.5A.
To protect the electrical components in the SANISAN
CONDENS, once the alarm has been triggered, any water
continuing to fill the tank comes out through the overflow
outlets in the cover.
7e
EXAMPLE OF AN INSTALLATION OF A SANISAN
E
(diameter 28).
A
(supplied : length 6 m).
®
CONDENS requires a
CONDENS to a conventional plug
®
Green/Yellow – Earth
® CONDENS
7d :
®