Inovonics EchoStream ES1265 Manuel D'installation Et D'utilisation page 2

Figure 4 ES1265 Lens Pattern
4. When the housing base has been attached to the ceiling, install the
PIR on the mounting bracket.
3 Test the ES1265
3.1 Walk Test
When in walk test mode the test LED will light every time the ES1265
senses motion. The unit will not transmit alarm signals during this test
period. There are two ways to initiate a walk test. Once initiated, the
walk test will last for one minute. To initiate a walk test:
1. With the cover on the unit, pass a magnet near the walk test reed
switch for less than ½ of one second, or press the test button for less
than ½ second.
Note: With the cover on, the reed switch is located on the opposite
side of the ES1265 as the housing screw (Fig 2).
Note: The test LED only lights during the walk test and the
transmission test.
3.2 Transmission Test
When in transmission test mode the unit will transmit alarm and
restoral cycles at regular intervals for approximately one minute. The
LED will light every time the unit transmits. To initiate a transmission
test:
1. With the cover on the unit, hold a magnet near the walk test reed
switch for at least one second, or press the test button for at least one
second.
Note: With the cover on, the reed switch is located on the opposite
side of the ES1265 as the housing screw (Fig 2).
4 Operation
The ES1265 signals an alarm condition when motion is detected by the
sensor. Once an alarm is signaled, further alarms are suppressed until no
motion is detected for a period of four minutes.
The ES1265 contains a tamper switch on the board (Fig. 2) to alert the
user if the housing cover is removed. The ES1265 also contains tamper
contacts in the mounting bracket to alert the user if the unit is removed
from the wall.
5 Specifications
Dimensions: 5.2" x 2.25" (131mm x 57mm)
Weight: 6.52 oz. (185g)
Detection method: 4-element PIR
Operating temperature: 32°F to 120°F (0°C to 49°C)
Humidity: 10% to 90% non-condensing
Battery: Inovonics BAT604 (3.0V lithium Duracell DL123A)
Note: Battery is supervised
Typical battery life: 2 years in location with low to moderate activity
Visible light protection: Stable against halogen light 8 feet (2.4m)
or reflected light
Temperature compensation: Yes
Pulse count: Selectable single pulse or multiple pulse
Frequency: 868-869 MHz (Europe), 915-928 MHz (Australia), 921-928
MHz (New Zealand), 902-928 MHz (USA)
6 Warranty/Disclaimer
Caution: Changes or modifications to this unit not expressly approved
by Inovonics Wireless Corporation may void the installer's authority to
operate the equipment as well as the product warranty.
Inovonics Wireless Corporation ("Inovonics") warrants its products
("Product" or "Products") to conform to its own specifications and to be
free of defects in materials and workmanship under normal use for a
period of twenty-four (24) months from the date of manufacture. Within
the warranty period, Inovonics will repair or replace, at its option, all or
any part of the warranted Product. Inovonics will not be responsible for
dismantling and/or reinstallation charges. To exercise the warranty, the
User ("User", "Installer" or "Consumer") must work directly through
their authorized distributor who will be given a Return Material
Authorization ("RMA") number by Inovonics. Details of shipment will be
arranged directly through the authorized distributor.
This warranty is void in cases of improper installation, misuse, failure to
follow installation and operating instructions, alteration, accident or
tampering, and repair by anyone other than Inovonics.
This warranty is exclusive and expressly in lieu of all other warranties,
obligations or liabilities, whether written, oral, express, or implied.
There is no warranty by Inovonics that Inovonics product will be
merchantable or fit for any particular purpose, nor is there any other
warranty, expressed or implied, except as such is expressly set forth
herein. In no event shall Inovonics be liable for an incidental,
consequential, indirect, special, or exemplary damages, including but
not limited to loss of profit, revenue, or contract, loss of use, cost of
down time, or interruption of business, nor any claim made by
distributor's customers or any other person or entity.
This warranty will not be modified or extended. Inovonics does not
authorize any person to act on its behalf to modify or extend this
warranty.
This warranty will apply only to Inovonics Products. Inovonics will not
be liable for any direct, incidental, or consequential damage or loss
whatsoever, caused by the malfunction of Product due to products,
accessories, or attachments of other manufacturers, including batteries,
used in conjunction with Inovonics Products.
Note: E-mail support@inovonics.com for a copy of the CE Declaration
of Conformity.