Performance Data Sheet - Monogram ZIC303NPPII Manuel Du Propriétaire

Masquer les pouces Voir aussi pour ZIC303NPPII:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

PERFORMANCE DATA SHEET

data sheet and at iapmort.org.
Substance Tested for Reduction
Chlorine Taste and Odor
Chloramine Taste and Odor
Particulate, Class I
Cysts
Lead
Mercury
Asbestos
Toxaphene
VOC (Chloroform surrogate chemical)
Alachlor
Atrazine
Benzene
Carbofuran
carbon tetrachloride
chlorobenzene
chloropicrin
2,4-D
dibromochloropropane (DBCP)
o-Dichlorobenzene
p-Dichlorobenzene
1,2-dichloroethane
1,1-dichloroethylene
cis-1,2-dichloroethylene
trans-1,2-dichloroethylene
1,2-dichloropropane
cis-1,3-dichloropropylene
dinoseb
Endrin
Ethylbenzene
ethylene dibromide (EDB)
bromochloroacetonitrile
dibromoacetonitrile
dichloroacetonitrile
trichloroacetonitrile
1,1-dichloro-2-propanone
1,1,1-trichloro-2-propanone
heptachlor (H-34, Heptox)
heptachlor epoxide
hexachlorobutadiene
hexachlorocyclopentadiene
Lindane
methoxychlor
pentachlorophenol
simazine
Styrene
1,1,2,2-tetrachloroethane
Tetrachloroethylene
Toluene
2,4,5-TP (silvex)
tribromoacetic acid
1,2,4-Trichlorobenzene
1,1,1-trichloroethane
1,1,2-trichloroethane
trichloroethylene
bromoform
bromodichloromethane
chlorodibromomethane
xylenes
Meprobamate
Atenolol
Carbamazepine
DEET
Metolachlor
Trimethoprim
Linuron
TCEP
TCPP
Phenytoin
Ibuprofen
Naproxen
Estrone
Bisphenol A
Nonyl phenol
PFOA/PFOS
18
Influent challenge
Maximum permissible
concentration
product water
(mg/L)
concentration (mg/L)
2.0 mg/L +/- 10%
N/A
3.0 mg/L +/- 10%
0.5
At least 10,000/mL
N/A
50,000/L
N/A
0.15
0.01
0.006
0.002
107 to 108 fibers/ L
N/A
0.015 +/- 10%
0.003
0.300
0.015
0.050
0.001
0.100
0.003
0.081
0.001
0.190
0.001
0.078
0.0018
0.077
0.001
0.015
0.0002
0.110
0.0017
0.052
0.00002
0.08
0.001
0.040
0.001
0.088
0.0048
0.083
0.001
0.170
0.0005
0.086
0.001
0.080
0.001
0.079
0.001
0.170
0.0002
0.053
0.00059
0.088
0.001
0.044
0.00002
0.022
0.0005
0.024
0.0006
0.0096
0.0002
0.015
0.0003
0.0072
0.0001
0.0082
0.0003
0.025
0.00001
0.0107
0.0002
0.044
0.001
0.060
0.000002
0.055
0.00001
0.050
0.0001
0.096
0.001
0.120
0.004
0.150
0.0005
0.081
0.001
0.081
0.001
0.078
0.001
0.270
0.0016
0.042
0.001
0.160
0.0005
0.084
0.0046
0.150
0.0005
0.180
0.0010
0.300
0.015
0.300
0.015
0.300
0.015
0.070
0.001
400 +/- 20%
60
200 +/- 20%
30
1400 +/- 20%
200
1400 +/- 20%
200
1400 +/- 20%
200
140 +/- 20%
20
140 +/- 20%
20
5000 +/- 20%
700
5000 +/- 20%
700
200 +/- 20%
30
400 +/- 20%
60
140 +/- 20%
20
140 +/- 20%
20
2000 +/- 20%
300
1400 +/- 20%
200
1.5 mg/L +/- 10%
0.07
Model: XWFE
Avg %
Application Guidelines/Water Supply Parameters
Reduction
Service Flow
96.9
Water Supply
96.9
91.4
Water Pressure
>99.99
Water Temperature
98.85
Capacity
96.3
It is essential that the manufacturer's recommended installation,
>99
maintenance and filter replacement requirements be carried out for
86.95
the product to perform as advertised. See Installation Manual for
99.7
Warranty information.
> 98
NOTE: While the testing was performed under standard
> 97
laboratory conditions, actual performance may vary.
> 99
Replacement Cartridge: XWFE. For estimated costs
> 99
98
of replacement elements please visit our website at
> 99
gewaterfilters.com.
99
98
WARNING
> 99
> 99
• Do not use with water that is microbiologically
> 98
95
unsafe or of unknown quality without adequate
> 99
disinfection before and after the system. Systems
> 99
certified for cyst reduction may be used on disinfected
> 99
water that may contain filterable cysts.
> 99
> 99
NOTICE
99
To reduce the risk of water leakage or flooding, and
99
to ensure optimal filter performance:
> 99
• Read and follow use instructions before installation and
> 99
98
use of this system.
98
• Installation and use MUST comply with all state and
98
local plumbing codes.
98
• Do not install if water pressure exceeds 120 psi (827
99
kPa). If your water pressure exceeds 80 psi (552 kPa),
96
you must install a pressure-limiting valve. Contact a
>99
98
plumbing professional if you are uncertain how to check
> 98
your water pressure.
> 99
• Do not install where water hammer conditions may
> 99
occur. If water hammer conditions exist you must
> 99
install a water hammer arrester. Contact a plumbing
> 99
professional if you are uncertain how to check for this
> 97
condition.
> 99
> 99
• Do not install on hot water supply lines. The maximum
> 99
operating water temperature of this filter system is 100º
> 99
F (38º C).
99
• Protect filter from freezing. Drain filter when
> 98
temperatures drop below 33ºF (0.6ºC).
> 99
• Change the disposable filter cartridge every six months
95
or sooner if you observe a noticeable reduction in water
> 99
> 99
flow rate.
95
• Failure to replace the disposable filter cartridge at
95
recommended intervals may lead to reduced filter
95
performance and cracks in the filter housing, causing
>99
water leakage or flooding.
95.5
• This System has been tested according to NSF/ANSI
95.9
98.6
42, 53, 401 and P473 for the reduction of the substances
98.6
listed below. The concentration of the indicated
98.7
substances in water entering the system was reduced
96.1
to a concentration less than or equal to the permissible
96.6
limit for water leaving the system, as specified in NSF/
98.1
ANSI 42, 53, 401 and P473.
98.1
96
95.9
96.5
97.1
99.1
97.3
99.25
0.5 gpm (1.89 lpm)
Potable Water
25-120 psi (172-827 kPa)
33°F-100°F (0.6°C-38°C)
170 gallons (643.5 liters)
To reduce the risk associated with
ingestion of contaminants:
XWFE System is certified by IAPMO R&T
against NSF/ANSI Standards 42,53, 401 and
P473 for the reduction of claims specified on
the performance data sheet and at
iapmort.org.
49-1000500 Rev. 1

Publicité

Table des Matières
loading

Table des Matières