REVELL Revellutions FLAME WING Mode D'emploi page 9

10 gear shIFTIng
This vehicle is equipped with mechanical
gear shifting.
10A Slow gear (e.g. for indoors or for
larger inclines): Slide the gear
change lever to the left until it locks
into place.
10B Fast gear (e.g. for outdoors or for
flat stretches): Slide the gear change
lever to the right until it locks into
place.
Attention! Do not switch while the
motor is running!
12 ChangIng The sprIngs
Front axle:
12A Pull the spring strut off of the upper pin.
12B Pull the spring strut off of the lower pin.
12C Gently turn the upper and lower sections in opposite directions so that they can be
pulled apart and remove the spring (bayonet connection). Now you can replace the
spring.
Assembly takes place in reverse order.
Rear axle:
12D Remove the wheels. Unhook the spring strut on the lower pin towards the back.
12E Turn the spring strut upwards to the position shown.
12F Pull the spring strut off of the upper pin.
12G Gently turn the upper and lower sections in opposite directions so that they can
be pulled apart and remove the spring (bayonet connection).
Now you can replace the spring.
Assembly takes place in reverse order.
InsTruCTIons For saFe drIvIng
GENERAL DRiViNG TiPS:
• Always move the controls slowly and with a gentle touch.
• Always maintain visual contact with the vehicle and do not look at the remote control!
• On initial driving attempts, there is a general tendency toward excessive movements
of the controls. Make sure that you have sufficient room.
• In order to drive along a curve, it often suffices to turn the controller very slightly in
the respective direction.
• Driving training: Ideally, you should practice on a large, empty parking lot. Set up two
empty plastic bottles approx. 5-10 metres apart. Now try to drive the vehicle around
these two bottles – as close as possible without knocking the bottles over. In the pro-
cess, carefully increase the speed. After you have drained the batteries approximately
two to three times for this process, you will be able to control your vehicle better.
After a crash, always release the speed control immediately in order to prevent
damage to the electronics.
16
11 Wheel Change
Press the retaining tang so that you can
pull the wheel off and fit another in its
place. When fitting the wheel, make
sure that the hexagon of the wheel hub
engages properly in the rim.
ThE SuiTABLE DRiViNG ENViRONMENT:
The location in which the vehicle is driven should fulfill the following criteria:
1. It should be a location in which there is as much open area as possible,
without disruptive obstacles.
2. Make absolutely sure when starting that there are no people or animals in the
immediate vicinity.
3. Always watch the vehicle so that it does not drive into the operator, other people
or animals and injuries them.
TroubleshooTIng
Problem: The wheels do not move.
Cause: • The battery is too weak or depleted.
Remedy: • Charge the battery (see chapter "Charging the vehicle").
Problem: Remote control does not work.
Cause: • The remote control is switched off.
• The batteries were not inserted correctly.
• The batteries do not have enough power.
Remedy: • Repeat the switch-on process as described.
• Check whether the batteries are inserted correctly.
Problem: The vehicle cannot be controlled with the remote control.
Cause: • The remote control is switched off.
• The connection between the remote control and vehicle has been severed.
Remedy: • Move the remote control switch to the "ON" position.
• Re-establish connection between the vehicle and remote control (see section 9).
Problem: The vehicle slows down and stops during travel for no apparent reason.
Cause: • The vehicle battery is too weak.
Remedy: • Charge the battery (see chapter "Charging the vehicle".
Problem: The remote control beeps and the LED blinks.
Cause: • The remote control's batteries are flat.
Remedy: • Exchanging and charging the batteries (see chapter "Charging the vehicle").
Problem: The car has stopped and beeps.
Cause: • The battery is empty.
Remedy: • Charge the battery (see chapter "Charging the vehicle").
Cause: • The remote control is switched off.
Remedy: • Switch on the remote control.
Problem: The gear lever springs back, the new gear does not engage.
Cause: • The gear cogs are not correctly aligned.
Remedy: • Put the vehicle on the ground, hold the gear lever in the desired position and
push it forwards slowly until the gear engages.
Additional tips and trick can be found online at www.revellutions.de.
servICe noTes
You can find ordering options, the online game and
useful information for all Revellutions models at
www.revellutions.de.
www.revellutions.de
17