Front Panel Display - Satelec ProphyMax Notice D'utilisation

1. Introduction
Front panel – Display
9. Boost indicator
Lights when the BOOST function is activated.
10. Standby indicator
Lights when the device is in standby mode (energy saving).
11. Display
The display background color indicates:
•
power on, the color indicator appears bluish white.
Any other color signals a malfunction (see chapter
troubleshooting).
•
in use, the color displayed (green, yellow, blue and
orange) corresponds to the color code of the
ultrasound power range selected.
The figures displayed indicate:
•
power on, the number 88 indicates the correct
operation of the segments of the display. Any other
value signals a malfunction of the indicator (see
chapter troubleshooting.
•
in use, the ultrasound power level (1 to 10) for the
range selected, controlled by the
22).
•
When programming:
the length of time of inactivity before the
-
device enters standby mode;
for Prophy Max™ Lux only, the length of time
-
before the light is switched off on the
Suprasson® Lux handpiece, when ultrasound
is no longer in use;
the display blanks out (black background and no figures)
when the device is in air polisher mode.
The following figure shows an example of the display, from
left to right, power on, in use (setting the ultrasound power
level) and when programming (light time limit).
2
12. Water supply indicator
Lights when the
indicates irrigation via the drinking water supply.
13. Irrigation kit indicator
Lights when the key is pressed (ref. 20), and indicates
irrigation via one of the two reservoirs.
14. Spray or dry mode indicator
Lights when the key is pressed (ref. 21).
15. Air polisher mode indicator
Indicates activation of air polishing mode when the
is pressed (ref. 23).
Sensitive controls panel
16. Ultrasound power ranges keys
Each yellow, green, blue and orange key corresponds to an
ultrasound power range, from the weakest to the strongest
keys (Ref.
as follows:
•
Green background: low power (ref. 16a).
•
Yellow background: intermediate power (ref. 16b).
•
Blue background: high power (ref. 16c).
• Orange background: very high power (ref. 16d).
The range selected:
•
a reminder is given by the color of the display
backlighting;
•
is programmed in the factory at level 5 except for the
orange key which is programmed at level 1 and uses
irrigation from the water supply.
The range may also be selected with the multifunction
footswitch (see chapter on the multifunction footswitch
pedal).
key is pressed (ref. 19), and
key
17. Boost
Applies the power (value 10) of the selected range; the
lights up. A second press on the key exits the mode.
This mode can also be accessed from the multifunction
footswitch (cannot be memorized and use must be
occasional).
18. Memory key
Memorizes a power level for each of the four power ranges,
with the exception of switching on irrigation and Boost.
19. Water supply key
Pressing this key selects drinking water (water supply) as
the irrigation solution. The indicator lights up. Irrigation will
only take place after the spray or dry
pressed; the rate of flow may be set via the handpiece
connector. The two keys 19 and 20 are both exclusive and
may be memorized.
20. Irrigation kit key
Pressing this key selects the irrigation kit (optional).
Irrigation will only take place after the spray or dry
(ref. 21) is pressed.
The rate of flow may be adjusted via the control knob on
the pump. The two keys 19 and 20 are both exclusive and
may be memorized.
21. Spray or dry key
Switches on irrigation after keys 19 or 20 have been
selected. The indicator (ref. 14) lights up. A second press
turns irrigation off.
22. The keys
Reduce ( key ) or increase ( key) ultrasound power in
the selected range. The values go from 1 to 10.
key (ref. 21) is
key