General Information; Safety Information - BARO Ontero XR In-Track Notice De Montage Et Mode D'emploi

Table des Matières

Publicité

Ontero XR
ENGLISH
Please read these instructions
before installing and using the
luminaire and keep them in a
safe place.

GENERAL INFORMATION

The luminaire is an LED lu-
minaire with a firmly attached
lamp. There are no provisions
for replacing the lamp. The lumi-
naire is wired ready for connec-
tion and complies with currently
valid standards and regulations.
The supply voltage is 220-240 V,
50/60 Hz. This luminaire com-
plies with protection class II.
The intended use is the illumina-
tion of items and objects in per-
manent interior rooms. The pro-
tection rating is IP 20. Any other
use does not count as intended
use. We reserve the right to make
modifications due to technical
advances. The technical data
of the valid data sheet applies
in each case. Damage caused by
disregarding the instructions is
not covered by the warranty. The
luminaire is designed for an am-
bient temperature of 25°C. Tem-
peratures above 40°C can damage
the luminaire and greatly shorten
the service life.

SAFETY INFORMATION

The luminaire may only be
mounted by qualified personnel.
The local installation regulations
must be adhered to during this
procedure. The mains supply
must be disconnected before in-
stallation and maintenance work
is carried out.
The luminaire becomes warm
during use and must therefore be
installed out of arm's reach. Cool-
ing openings must remain free of
dust and must not be covered. The
safety clearance to flammable ma-
terials must be adhered to.
The luminaire contains electro-
static sensitive components. Do
not touch the illuminating sur-
face. Mains transients or voltage
peaks can damage the luminaire.
The luminaire must be protected
against damage from grid-relat-
ed overvoltage. Damage caused
by overvoltage is excluded from
the terms of the guarantee.
The affixing of stickers or other
parts not authorized by BÄRO is
forbidden. Replacement and ad-
ditional parts must be procured
from or approved by BÄRO.
Luminaires that do not work
or flicker must be disconnected
from the power supply. Do not
look directly at the light source.
In the event of malfunctions
please inform BÄRO Service
(contact information on the last
page).
8
7
6
F
I
E
D
C
I
B
12
11
10
9
8
H
A
8
7
6
G
F
E
D
C
B
A
12
11
10
9
8
5
4
3
2
250
I
Ø91
I
0,54 kg
7
6
5
4
Diese Unterlage ist unser Eigentum. Jede Vervielfältigung, Verwertung oder Mitteilung an dritte Personen ist s
(Urhebergesetz, Gesetz gegen unlauteren Wettbewerb BGB). Alle Rechte für den Fall der Patenterteilung (A
BÄRO GmbH & Co. KG, 42799 Leichlingen
BÄRO GMBH & CO. KG
Allgemein-
Wolfstall 54-56
toleranzen
nach
D-42799 Leichlingen
DIN ISO 2768
t=
Tel. 02174/799-0
T1 mittel
Datum
Name
S 906-14
12.12.2018 Schuette
Erstellt
12.12.2018
Schuette
Bearbeitet
Geprüft
Änderungen oder technische Mängel,
die sich beim Prototypenbau oder der
Serienfertigung ergeben, sind
schriftlich der Fa. BÄRO mitzuteilen.
Status
Änderungen
Datum
Name
Dok.-Nr.
G
5
4
3
2
min. 250 mm
7
6
5
4

Publicité

Table des Matières
loading

Table des Matières