Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
NOTE: SIDE TERMINAL TO BE USED IN POSITIVE CLAMP ONLY!
21.
section 18f or 18g.
Storage position
Will not get lost. Always ready to use.
LENGTH OF CHARGE
22.
a.
Test the battery for state of charge. Do not charge if it is over 75% charged or the battery is determined to be defective.
b.
Set beginning amps charge rate for size of battery and state of charge per charts
c.
Charge for length of time per charge,
d.
Discontinue charge when the specific gravity of electrolyte reaches 1.260 or above. A temperature compensating hydrometer should be used
for this reading. Discontinue charge if the battery begins to gas excessively or if the temperature of the electrolyte reaches approximately
125°F. Do not overcharge batteries. Overcharging results in excessive water loss and eventual damage to the battery.
BATTERY SIZE TABLE
BATTERY SIZE
Ampere Hours
Reserve Capacity
Cold Cranking Amps
STATE OF CHARGE TABLE
STATE OF CHARGE
Specific Gravity
Open Circuit Voltage-6 V.
Open Circuit Voltage-12 V.
Open Circuit Voltage-24 V.
ASSEMBLY INSTRUCTIONS
Attach the handle to the charger using the four screws provided. Attach the front leg to the base with the four hex
head screws provided. To attach wheels and axle to the base, tap one axle nut onto the axle with a hammer,
slide one wheel onto the axle. Push the axle through the base, place wheel on opposite side. Tap axle nut onto
the axle with a hamm
er.
OPERATING INSTRUCTIONS
CAUTION
- This battery charger must be fully assembled before operating. Failure to do so may result in risk of
injury.
USE OF INSTRUMENT PANEL:
The MINUTES CHARGE timer has an OFF position, a CONTINUOUS CHARGE position and a timed charge
range from 0 to 90 minutes.
a. OFF - Always make sure the timer is in the OFF position before connecting or disconnecting the clamps from
the battery. The charger will not charge with the timer in this position.
b. CONTINUOUS CHARGE - This position is used for slow charging or parallel charging and will not turn the
charger off. Do not use this position for fast charging.
c. 0 to 90 MINUTES TIMED CHARGE - The timer will automatically turn the charger off at the end of the pre-set charging time. Turn the timer past
20 before setting the desired time.
d. VOLTS CHARGE AND AMPS CHARGE - These switches are used to regulate the output voltage and current of the battery charger.
TO CHARGE BATTERIES
Make connections to the battery per the instructions in preceding section of this manual. Determine the battery voltage and turn the VOLTS
CHARGE switch to the lowest appropriate setting. Turn the AMPS CHARGE switch to "LO". Turn the timer on. If a higher rate of charge is
desired, advance the AMPS CHARGE switch to a higher position. If the charge rate is still not satisfactory, return the AMPS CHARGE switch to
"LO" and advance the VOLTS CHARGE switch one position. Adjust the AMPS CHARGE switch to the desired rate.
Extended position
Note: Pressure, when handle is squeezed,
holds adapter firm. Will not slip back.
SMALL
MEDIUM
LARGE
40
60
80+
60
90
100+
275
350
400+
75%
50%
25%
DEAD
1.110
1.225
1.185
1.140
5.9
6.2
6.05
5.95
11.8
12.4
12.1
11.9
23.6
24.8
24.2
23.8
For instructions for NEGATIVE clamp attachment refer to
CHARGE RATE Vs. MINUTES CHARGE
BATTERY SIZE %CHARGE
0-25
SMALL
25-50
50-75
0-25
MEDIUM
25-50
50-75
0-25
LARGE
25-50
50-75
3
Thrust on terminal
Note: Clamp is released and spring tension
holds adapter firm.
MINUTES
15 30 45 60 75 90
45
30
30
25
25
30
20
20
15
15
A
M
15
10
10
10
5
P
70
50
45
40
35
E
R
45
30
25
20
20
E
25
15
15
10 10 10
S
90
55
55
50
45
60
40
35
30
30
30
20
20
15 15 15
20
10
5
30
20
45
30
Publicité
Table des Matières
