Display; Factory Reset; Exit Menu; Error Messages - True Comfort PS120/240TP2 Manuel De L'utilisateur

Type PS120/240TP2

Display

I want to choose the information to be shown on the
thermostat display.
To do so, you must:
1 Press the OK button twice to activate the menu.
2 Press the Up or Down buttons until the Settings option
flashes.
3 Press the OK button.
4 Press the Up or Down buttons until the Display option
flashes.
5 Press the Up or Down buttons to select whether you wish to:
- display the Clock or not (On/Off),
- display the Set temperature or not (On/Off).
You can also decide whether the temperature displayed is:
- the Room temperature,
- the Floor temperature (if a floor sensor is used), or
- the Regulator temperature.
6 Press the OK button to confirm the settings as you work your
way through the various options in the Display submenu.
7 Select Exit to exit the option.
Factory settings:
- TIME: ON
- Set temp.: ON
- Floor temperature is shown
FLOOR
TIME
DAY
CHILDLOCK
SETTINGS C°/F°
APPLICATION
OFFSET TEMP
READOUT
ADAPTIVE
DISPLAY

FACTORY RESET

EXIT
AM
Factory Reset
I want to return to the factory settings.
To do so, you must:
1 Press the OK button twice to activate the menu.
2 Press the Up or Down buttons until the Settings option flashes.
3 Press the OK button.
4 Press the Up or Down buttons until the Factory Reset option
flashes.
5 Press the OK button. A submenu will appear.
6 Press the Up or Down buttons until the Reset option flashes.
7 Press the OK button.
8 Select Exit to exit the option.
Please note: The date and time cannot be reset.
TIME
DAY
CHILDLOCK
SETTINGS C°/F°
APPLICATION
OFFSET TEMP
READOUT
ADAPTIVE
DISPLAY
FACTORY RESET
EXIT
6
Room/floor/regulator
On/Off
On/Off
RESET
EXIT
© 2016 OJ Electronics A/S

Exit Menu

I want to exit a menu.
To do so, you must use the Exit option:
The various menus and submenus contain an Exit option.
1 Press the Up or Down buttons until Exit flashes.
2 Press the OK button. You may have to repeat steps 1 and 2 to
return to the final Exit option.
Please note: When you activate a menu, the menu item last se-
lected will begin flashing. This allows you to view the latest setting.
If, for example, you activate the Mode menu, Man. mode will flash
if you used Man. mode the last time.
This principle also applies to current temperature/time settings.
When you enter the various menus, they always display the value
that was last selected. This allows you to check the current set-
tings.
Should you enter a menu by mistake, you can exit it again without
changing the setting by simply confirming the current setting, i.e.
by clicking the OK button.

Error Messages

E0 = Internal failure. Replace thermostat.
E1 = Internal sensor defective or short-circuited.
Replace thermostat.
E2 = External sensor defective or short-circuited.
Check external sensor.
Factory Settings for Automatic 5:2 Program
Days 1-5 (Monday - Friday)
Event Time
Morning 6:00 a.m. - 8:00 a.m.
Out 8:00 a.m. - 4:00 p.m.
Home 4:00 p.m. - 10:00 p.m.
Night 10:00 p.m. - 6:00 a.m.
Days 6-7 (Saturday - Sunday)
Event Time
Day 8:00 a.m. - 11:00 p.m.
Night 11:00 p.m. - 08:00 a.m.
English
Temperature
77 °F / 25 °C
68 °F / 20 °C
77 °F / 25 °C
68 °F / 20 °C
Temperature
77 °F / 25 °C
68 °F / 20 °C