True Comfort PS120/240TP2 Guide Rapide

Q U I C K G U I D E
Type PS120/240TP2
67584 02/16 (LOA)
Introduction
This thermostat can switch on your heating system at predetermined
times on different days of the week. For each day of the week, you can
set individual temperatures for 4 periods, called events. The thermostat
comes with a default schedule suitable for most installations. Unless you
change the settings, the thermostat will operate in compliance with the
default schedule. Lowering the temperature when the home is unoccu-
pied will reduce your energy costs without reducing comfort.
Furthermore, the thermostat features an adaptive function that auto-
matically changes heating period start times so as to ensure that the
required temperature is reached at the required time.
GFCI test button
Up button
OK button
On/Off button
Down button
Reset GFCI
FIRST TIME SETTINGS
• Time and day:
The first time you turn on the thermostat, time and day must be set.
The time flashes. Set the current time using the Up or Down button.
Then press the OK button to confirm the time. The day of the week
will then flash. Select the current day using the Up or Down button.
Press the OK button.
• Select Mode:
The thermostat features 3 different modes of temperature control:
Auto: Controlled automatically via the 4-event schedule.
Override: Change the temperature for a single event.
Manual: Set a temperature manually. 4-event program is
cancelled.
Press OK to access Mode and select the required mode using the
Up or Down button. Press the OK button.
• Select Schedule:
The weekly 4-event schedule:
5:2: Mon-Fri with 4 events/Sat-Sun with 2 events.
6:1: Mon-Sat with 4 events/Sun with 2 events.
7:0: Mon-Sun with 4 individual events.
Press the Up or Down button until the Schedule option flashes.
Press OK and then press the Up or Down button until the required
program (5:2, 6:1 or 7:0) flashes. Confirm with OK.
The thermostat is now ready for use.
How to program the thermostat
The thermostat is pre-programmed with a 4-event program, see Fac-
tory Settings below. The program can be adapted individually for the
following 4-events:
• when I wake up in the morning
• when I am away at work
• when I come home
• and at night
1 Press the Up or Down button until the Program option flashes.
Press the OK button.
2 Press the Up or Down button until the day(s) that you wish to
program flash in the lower part of the display, e.g. Mon Tue Wed
Thu Fri. Press OK.
3 The symbol for the first event
The hour will flash, allowing you to set the hour at which you
want the morning period to begin. Press the Up or Down button
until the required hour is displayed.
will now flash.
The trademark is registered and belongs to OJ Electronics A/S · © 2016 OJ Electronics A/S
4 Press the OK button. The minutes will flash.
Press the Up or Down button until the required minutes are
displayed, press OK.
5 The temperature setting will now flash in the upper part of the
display. Press the Up or Down button to set the required tem-
perature. Press the OK button.
6 The symbol for the next event (e.g. at work) will now flash, allow-
ing you to set the time and temperature for this period of the day
by repeating steps 3-5.
7 Once the four events have been set for all days, the display will
return to the Program menu. Finally, select Exit to exit the Pro-
gram for a 5:2 schedule.
Ground Fault Circuit Interrupter (GFCI)
The thermostat has a built-in GFCI that ensures personal safety in case
of ground faults.
It is important that the GFCI is checked monthly.
Settings
The Settings option allows the following to be set:
Time: Set the hour and minutes.
Day: Set the actual day.
Child lock: Activate the child lock. To unlock, press OK to
activate the menu, then hold the Up and Down
buttons simultaneously for 3 seconds.
°C / °F: Choose between Celsius and Fahrenheit.
Application: Select the type of control used:
Room/Floor/Regulator/Room limit.
Offset temp: Adjust the measured temperature.
Readout: Readout of energy consumption in per cent,
software version and application.
Adaptive: Ensures the required temperature is reached at
the programmed time.
Display: Select what is shown on the default display.
Factory reset: Restore factory settings.
Exit Menu
The various menus and sub-menus contain an Exit option.
1 Press the Up or Down button until Exit flashes.
2 Press the OK button. You may have to repeat steps 1 and 2 to
return to the final Exit option.
Should you enter a menu by mistake, you can exit it again without
changing the setting by simply confirming the current setting, i.e. by
clicking the OK button.
Factory Settings for Automatic 5:2 Program
Days 1-5 (Monday - Friday)
Event Time
Morning 6:00 a.m. - 8:00 a.m.
Out 8:00 a.m. - 4:00 p.m.
Home 4:00 p.m. - 10:00 p.m.
Night 10:00 p.m. - 6:00 a.m.
Days 6-7 (Saturday - Sunday)
Event Time
Day 8:00 a.m. - 11:00 p.m.
Night 11:00 p.m. - 08:00 a.m.
The full manual can be downloaded at:
http://www.truecomfortsystems.com/sites/default/
files/User%20manual-Programmable.pdf
English
Temperature
77 °F / 25 °C
68 °F / 20 °C
77 °F / 25 °C
68 °F / 20 °C
Temperature
77 °F / 25 °C
68 °F / 20 °C
1