Bosch PWS 10-125 CE Mode D'emploi page 20

OBJ_BUCH-972-002.book Page 20 Wednesday, October 19, 2011 4:00 PM
20 | English
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales
service agent for maintenance for addresses, see section "Af-
ter-sales Service and Customer Assistance".
Protection Guard for Grinding
Place the protection guard 7 onto
the spindle collar as shown in the
illustration. The triangle marks on
the protection guard must corre-
spond with the respective marks
on the gear case.
Press the protection guard 7 onto
the spindle collar until the shoul-
der of the protection guard is
seated against the flange of the
machine, and turn the protection
guard until it can clearly be heard
to engage.
Adjust the position of the protec-
tion guard 7 to the requirements
of the work process. For this, press the release lever 1 up-
ward and turn the protection guard 7 to the required position.
Adjust the protection guard 7 in such a manner that
sparking is prevented in the direction of the operator.
The protection guard 7 may be turned only upon actua-
tion of the release lever 1! Otherwise the power tool
may not continue to be used under any circumstances
and must be taken to an after-sales service agent.
Note: The encoding keys on the protection guard 7 ensure
that only a protection guard that fits the machine type can be
mounted.
Protection Guard for Cutting
For cutting with bonded abrasives, always use the pro-
tection guard for cutting 12.
Provide for sufficient dust extraction when cutting
stone.
The protection guard for cutting 12 is mounted in the same
manner as the protection guard for grinding 7.
Cutting Guide with Dust Extraction Protection Guard
The cutting guide with dust extraction protection guard 19 is
mounted in the same manner as the protection guard for
grinding 7.
Auxiliary Handle
Operate your machine only with the auxiliary handle 5.
Screw the auxiliary handle 5 on the right or left of the machine
head depending on the working method.
1 609 929 S67 | (19.10.11)
Hand Guard
For operations with the rubber sanding plate 15 or with
the cup brush/wheel brush/flap disc, always mount the
hand guard 14.
The hand guard 14 is fastened with the auxiliary handle 5.
Mounting the Grinding Tools
Before any work on the machine itself, pull the mains
plug.
Do not touch grinding and cutting discs before they
have cooled down. The discs can become very hot while
working.
Clean the grinder spindle 6 and all parts to be mounted.
For clamping and loosening the grinding tools, lock the grind-
er spindle with the spindle lock button 2.
Actuate the spindle lock button only when the grinder
spindle is at a standstill. Otherwise, the machine may be-
come damaged.
Grinding/Cutting Disc
Pay attention to the dimensions of the grinding tools. The
mounting hole diameter must fit the mounting flange without
play. Do not use reducers or adapters.
When using diamond cutting discs, pay attention that the di-
rection-of-rotation arrow on the diamond cutting disc and the
direction of rotation of the machine (see direction-of-rotation
arrow on the machine head) agree.
See graphics page for the mounting sequence.
To fasten the grinding/cutting disc, screw on the clamping nut
10 and tighten with the two-pin spanner; see Section "Quick-
clamping Nut ".
After mounting the grinding tool and before switching
on, check that the grinding tool is correctly mounted
and that it can turn freely. Make sure that the grinding
tool does not graze against the protection guard or oth-
er parts.
A plastic part (O-ring) is fitted around
the centring collar of mounting flange 8.
If the O-ring is missing or damaged,
the mounting flange 8 must be replaced
before resuming operation.
Flap Disc
For operations with the flap disc, always mount the
hand guard 14.
Rubber Sanding Plate
For operations with the rubber sanding plate 15, al-
ways mount the hand guard 14.
See graphics page for the mounting sequence.
Screw on the round nut 17 and tighten with the two-pin span-
ner.
Bosch Power Tools