Cycle Guide - Amana ADB1100AWS2 Mode D'emploi

Powder and Gels
The amount of detergent to use depends on:
How much soil remains on the items - Heavily soiled loads require
more detergent.
The hardness of the water - If you use too little detergent in hard
water, dishes won't be clean. If you use too much in soft water,
glassware will etch.
Soft to Medium Water (0-6 grains per U.S. gallon) [typical water
softener water and some city water]
Medium to Hard Water (7-12 grains per U.S. gallon) [well water
and some city water]
Depending on your water hardness, fill the Main Wash section of
the dispenser as shown. Fill the Pre-Wash section to the level
shown, if needed.
NOTE: Follow instructions on the package when using other
dishwasher detergent types.
4.
Add Rinse Aid
Your dishwasher is designed to use rinse aid for good drying
performance. Without rinse aid, your dishes and dishwasher interior
will have excessive moisture. The Heat Dry option will not perform
as well without rinse aid.
Rinse aid keeps water from forming droplets that can
dry as spots or streaks. It also improves drying by
allowing water to drain off of dishes after final rinse.
To add rinse aid, turn the
dispenser cap to "Refill" and lift
off. Pour rinse aid into the
opening until indicator level is
at "Full." Replace dispenser
cap and turn to "Lock." Make
sure cap is fully locked.
This information covers several different models. Your dishwasher may not have all of the cycles and options described.
Use for hard-to-clean, heavily soiled pots, pans, casseroles, and
tableware.
This cycle is recommended to completely wash a full load of
normally soiled dishes. Selecting this cycle will default to the
options recommended for normal amounts of food soil. The
energy label is based on this cycle.
For fast results, 1-Hour Wash will clean dishes using slightly
more water and energy. For improved drying, select the Heated
Dry option.
USE RINSE AID FOR
Full
BETTER DRYING
Lock
Add
Refill

CYCLE GUIDE

CYCLES
NOTE: For most water conditions, the factory setting will give good
results.
Check water hardness level to ensure no rings
or spots on your dishware before adding rinse
aid or adjusting the factory setting.
If you are experiencing poor drying
performance, you may want to try a higher
setting.
Turn the arrow adjuster inside the dispenser to
change rinse aid setting.
5.
Select a Cycle (cycles vary by model)
Efficient dishwashers run longer to save water and energy, just as
driving a car slower saves on gas. Typical cycle time is approximately
2¹⁄₂ hours, but can take less or more time to complete depending on
selections.
6.
Select Options (options vary by model)
You can customize your cycles by pressing the options desired. If you
change your mind, press the option again to turn off the option. Not all
options are available for every cycle. If an invalid option is selected for a
given cycle, the lights will flash.
Full
7.
Start or Resume a Cycle
NOTE: Run hot water at the sink nearest your dishwasher until the
Add
water is hot. Turn off water.
IMPORTANT: If anyone opens the door (such as, for adding a dish,
even during the Delay Hours option), the START/RESUME button must
be pressed each time.
Push door firmly closed. The door latches automatically. Select the
wash cycle, options and press START/RESUME or press START/
RESUME to repeat the same cycle and options as in previous wash
cycle.
SOIL LEVEL
All soil levels
All soil levels
All soil levels
WASH TIME* (MINS.)
W/O OPTIONS
TYPICAL MAX
122 125
88 91
59 62
WATER
USAGE
GALLONS
(LITERS)
7.47 (28.28)
3.01 (11.38)
5.80 (21.94)