CombiSteel 7455.1662 Mode D'emploi page 13

12. Double Quantity cooking
1) Through the use of the X2 pad, the user can easily set the time two of a particular food item.
2) If the "X2" button is pressed in ready mode, followed by the starting of a Pre-set Program, or if the "X2" button
is pressed in 5 seconds of starting a Pre-set Program, the oven will start cooking with the quantity pre-set cooking
time.
3) Press "X2", "DOUBLE" displays. When press number buttons, the screen will display the quantity pre-set time.
For example, number button "5" and its pre-set time is 1 minute. Then press "X2", then time will change to
1:00*(1+0.8)=1:48(1 minute and 48 seconds).
4) When cooking program finish, the oven will enter End of Cook Cycle Mode.
13. Stage Cooking Programming
This allows the user to cook food items at manual cook mode and programming mode.
1) Three stages can be set at most under cooking mode or programming mode. After setting the power and time
for the first stage, press " Time Entry " to set the second stage. And the same step to set the third stage.
2) When setting the second, third stage, press " Time Entry", "S-2","S-3" displays.
3) Press " " button to start cooking.
Example: In programming mode, press number buttons "3" to set two stages cooking. The first stage is PL 7 and
time is 1 minute 25 seconds. The second stage is PL5 and 5 minutes and 40 seconds. The steps are as follows:
a. Ready state, press number button "1" for 5 seconds, " ProG " displays.
b. Press number button "3", the screen will display "P:03", after two seconds, the screen will display the related
time " :30".
c. Press "1","2","5" to input the cooking time. "1:25" displays.
d. Press "Med-Hi 70%", "PL7" displays. The first stage is finished.
Press " Time Entry", "S-2" displays.
e.
f. Press "5", "4","0" button, "5:40" displays.
g. Press "Medium 50%", "PL5 " displays. The second stage is finished.
h. Press " " button to start cooking.
i. The total time counts down.
14. Use Option Mode
1) Open the oven door and press "2" for 5 seconds. The buzzer sounds once and enters this mode.
2) The screen displays "OP: - -".
3) Press any number button to enter related mode setting. For example: to set the voice of the buzzer to medium.
Press " 2 ", "OP:22" displays. If you want to change, keep pressing "2", LED displays "OP:20", "OP:21","OP:22",
"OP:23", "OP:20" .....in cycle.
4) Press " " to save the current setting. After saved, "OP: - -" display again.
5) During setting process, press " " to enter Door Open Mode. Close the door will enter Ready Mode.
6) If " " button not pressed at the last step, the program cannot be saved but stay at previous way.
15. Service Mode
1) Open the oven door and press "3" pad for 5 seconds to enter service mode.
2) The screen displays "SERVICE".
3) To check the times of closing or opening the door, just press number button "3", the screen will display the
times.
4) Press " 1 " pad for Tube Hours.
Press " 2 " pad for Tube Cycles.
Press " 3 " pad for Door Cycles..
Press " 4 " pad to Clear service information.
Only for some models:
Press " 5 " pad to run Top Mag. Oven displays amps.
Press " 6 " pad to run Bottom Mag. Oven displays amps.
5) Press " " to enter Door Open Mode. Close the door will enter Ready Mode.
www.combisteel.com
13