Programming Mode - CombiSteel 7455.1662 Mode D'emploi

8. End of Cook Cycle Mode
1) After the time has expired in a Manual Cook Mode, or a Pre-set Program Cook Mode, the oven shall go into
The End of Cook Cycle Mode.
2) During this mode, "END" displays.
3) If either User Option OP:11 or "OP:12" is selected, the oven shall continue to sound until the user
acknowledges this by either opening and closing the door or pressing the " " pad. If User Option OP:10 is
selected, after the 3 second beep, the oven shall go into Idle Mode.
9. Pre-set Program Cook Mode
1) This mode allows cooking of food items through a one pad touch operation. While in Ready Mode, pressing
one of ten digit keys on the keyboard will cause the oven to run the Pre-set Program associated with that key.
2) During this mode, displays the remaining cooking time. If it is multi-stage cooking, the total remaining cooking
time displays not a particular stage cooking time.
3) When cooking program finish, the oven will enter End of Cook Cycle Mode. If you press " " button under this
mode, the oven will enter Pause Mode.
10. On the Fly Cooking
1) While the oven is cooking, if User Option OP:51 is selected, press number buttons, the pre-set cooking
program will start automatically.
2) The screen displays the remaining cooking time.
3) When cooking program finish, the oven will enter End of Cook Cycle Mode. If you press " " button under this
mode, the oven will enter Pause Mode.

11. Programming Mode

This mode allows the user to assign cook times and power levels to the once touched button.
1) Open the door and press "1" pad for 5 seconds, the buzzer will sound once and enter to Programming Mode.
2) "ProG" displays. You can press number keys to input the time you need.
3) Press "Hold 0%","Defrost 20%","Medium 50%" or "Med-Hi 70%" to input the power level. The screen will
display the related power. If the same button pressed twice, the power will change to PL10. If no power chosen,
"PL 0" is default. NOTE: Set the time first, then choose the power.
4) To change the cooking factors: If press "X2", the screen will display "CF:XX". The default factor is 80%. "CF:80"
displays. If you need to change the cooking , just press one the number buttons to set.
5) After setting the time and power, press " ", the cooking program will be saved. When the program saved,
"ProG" displays.
6) If all the cooking time exceeds the MAX. time User Option 7, when press " " to save the program, the buzzer
will sound three times briefly to tell you the time is no use. And then turns back to display "ProG". The time set
before will be no change.
7) Close the door, the oven will turn back to Ready Mode. If press " " button during setting process, the oven
turn to Door Open Mode. The program that not saved will be lost. If there is program saved as memory procedure,
press the related number button, the saved program will start. If no saved program, the buzzer will alarm when
pressing number button and it will not work. For example: set the program as memory cooking. Power level PL7
and cooking time is 1 minute and 25 seconds.
Step 1: In ready mode, press number button "1" for 5 seconds, "ProG" displays.
Step 2: Press number button "3", the screen will display "P:03", after two seconds, the screen will display the
related time " :30".
Step 3: Press number buttons "1", "2" and "5" to input the cooking time.
Step 4: Press "Med-Hi/70%" button,"PL7" displays. Setting finished.
Step 5: Press " " to save. When use the program next time, just press "3", the related program will start.
Note:
1. If the electricity is cut off, the saved program will not be lost.
2. If the program needs to reset , just repeat the above steps.
3. If press " " at the last step, it will turn back to Ready Mode. The setting will be no use.
12
www.combisteel.com