Basic Parameters - Retekess TD157 Manuel D'utilisation

Basic Parameters

Dimension：
Material：
Power Supply：
Support Pager：
IP Grade：
Dimension：
Material：
Receiving Sensitivity：
LI-Polymer：
Standby Time：
Reminder mode：
IP Grade：
Instructions
1.Note
1.1.Before operation, you need to put all pagers in the keyboard charging slot, and charging for 20
minutes.
1.2.The antenna must be installed on the keyboard before you using it to call the customer, otherwise it
will seriously affect the calling distance.
1.3.After modifying any settings (keyboard ID, change calling mode, change call duration time), you
need to re-pair the calling keyboard with the pager. Therefore, we recommend that your setting
sequence is: set the calling mode-set the call duration-pair the pager with the call keyboard.
1.4.Power on: Place all pagers in the charging slot of the calling base, and the pagers will automatically
turn on after the power of the calling base is connected.
1.5.Power off: Put all pagers in the charging slot of the calling base, enter [999+CALL] on the keyboard.
Note: The pager needs to be paired with the call keyboard, then it can be shut down normally.
1.6.Enter the setting mode: short press the [CALL] key and the [DEL] key at the same time, the
keyboard screen displays [F1], at this time input the corresponding number "1-4" from the keyboard to
select the mode, and press [ CALL] key to enter the setting mode, after the setting is completed, short
press the [DEL] key to exit the setting mode, the standby screen displays [---].
1.6.1.Input the number "1": [F1] Keyboard ID number
1.6.2.Input the number "2": [F2] Pager ID number setting (pair)
1.6.3.Input the number "3": [F3] Calling mode setting
1.6.4.Input the number "4": [F4] Calling duration time setting
1.7. Operation process: We recommend you firstly set the [F1] keyboard ID number setting, followed by
the [F3] calling mode setting and [F4] calling duration time setting, after completing the above opera-
tions, finally set the [F2] pager ID number setting.
2.[F1] Keyboard ID number setting
Enter the setting mode, choose F1 and enter [CALL],the screen displays the default keyboard ID
number of this keyboard. At this time, input the new number "001-999" on the keypad, and short press
the [CALL] key to save.
Note: If there is no special requirement, please do not modify the keyboard ID number, otherwise all
pagers need to be paired with the keyboard again, then they can be used. Do not set the base number
to "000".
3.[F2] Pager ID number setting(pair)
3.1.Firstly remove all pagers from the base, then enter the setting mode, the screen displays "F1", press
[2+CALL] to enter the pairing mode, enter the 3-digit number (001-998) you want to pair, and put the
pager into the charging slot, the 4 lights of the pager will flash, indicating that the setting is successful.
Then removing the pager, set the next one in sequence until all the pagers are set and short press the
[DEL] key to exit.
3.2.Please do not set "999" as a pager number, this number is a [Power off] command.
3.3.If you need to modify the pager number, just overwrite the old number with the new number.
4.[F3] Buzzer switch setting
Enter the setting mode, the default screen displays "F1", enter [3+CALL] to enter the
buzzer switch setting mode, at this time the screen display the current buzzer mode. You can enter
[000] to buzzer off or [001] to buzzer on, short press the 【CALL】key to save.
5.[F4] Calling duration setting
Enter the setting mode, the default screen flashes "F1",enter [4+CALL]to enter calling
duration setting, Enter "001-099" on the keyboard to set seconds of calling duration, short press the
【CALL】key to save.
Keyboard
238*151*30mm
ABS
DC12V/1A
998(16/SET)
IP32
Pager
106*51*11mm
ABS
-114dB
3.7V/150mAh
≈20 Hour
Beep+ Flashing
IP32
1