Niko 05-090-10 Mode D'emploi page 15

3.1.1. Light 1 and Light 2
Light 1 and Light 2 have one page each, from which up to 7 light circuits can be separately controlled. You can control a
total of 14 light circuits per room.
- Switched lighting: a switched light circuit can only be switched ON or OFF. Click on the light circuit to select it. Press the
CH+ button (11) to switch this light circuit ON. Press the CH- button (10) to switch this light circuit OFF.
- Dimmable lighting: Click on the light point that can be dimmed. Press buttons CH+ and CH- to switch this light point ON
and OFF. Press the VOL+ button (8) to dim UP. Press the VOL- button (7) to dim DOWN. Press the MUTE button (9) to
temporarily switch the sound of a connected Allegretto audio distribution system ON or OFF.
3.1.3. Roll-down shutters
You can control 6 roll-down shutters or curtains per room. Select the roll-down shutter or curtain you wish to control. Press
the button VOL+ (button 8) to open the roll-down shutter or curtain. Press the button VOL- (button 7) to close the
roll-down shutter or curtain. You can stop a moving shutter by pressing button VOL+ or VOL-. Press the MUTE button (9)
to temporarily switch the sound of a connected Allegretto audio distribution system ON or OFF.
3.1.5. Light atmospheres
You can prompt 8 light atmospheres per room. You can distinguish between day and night/evening atmospheres. Press the
light atmosphere that has to be activated. Press the CH+ button to switch the light scene ON. Press the CH- button to switch
the light scene OFF. Press the buttons VOL+ and VOL- to dim the entire light atmosphere up or down respectively. If you
wish to save a new light atmosphere, set the individual light points (using the light windows). Then press the light atmosphere
button and press the CH+ button for some time. The new light atmosphere has now been saved. Press the MUTE button (9)
to temporarily switch the sound of a connected Allegretto audio distribution system ON or OFF.
3.2. Controlling the Allegretto functions
You can also control the functions of the Allegretto audio distribution system directly. You must point the Pronto remote control towards the Allegretto audio
distribution system. The Allegretto appliance must therefore be placed in the room where the operation is carried out. Go to the opening window using the
Home button (1). Click on the Allegretto logo. Select an audio zone. Then select a source. Control the volume with the VOL+ and VOL- buttons (8 and 7).
Press the CH+ (11) button to select the next source. Press the CH- (10) button to select the previous source. Press the MUTE button (9) to temporarily
switch the sound of a connected Allegretto audio distribution system ON or OFF.
In the Allegretto windows, the following buttons are also available:
Switch the Allegretto installation ON and OFF
Go to the Presets window
Go to the Sound window
Go to the Zone window
Go to the Sources window
Via the Sound window, you can adjust the settings for Bass, Treble and Balance. In this window, you can also
select a different source.
3.1.2. Appliances
You can switch 6 appliances per room. Select the appliance you wish to switch. Use the CH+ and CH- buttons (11 and 10)
to switch the appliance ON or OFF. Press the MUTE button (9) to temporarily switch the sound of a connected Allegretto
audio distribution system ON or OFF.
3.1.4. Audio
You can operate the Allegretto audio distribution system from 10 rooms (zones) using the Nikobus audio interfaces and
IR bus push buttons. As the Allegretto installation is not located in these rooms, this is an indirect control.
The layout of the buttons on the audio window is similar to that of an 8-fold audio bus push button. Press the lower
left button to switch the audio zone ON/OFF. Press the upper left button to select the next source. With buttons 1, 2,
3 and 4, you directly select the desired source. Press the buttons on the right to control the volume within a zone.
You can also control the volume using the hardware buttons VOL+ and VOL-. Press the CH+ button (11) to select a
next source. Press the MUTE button (9) to temporarily switch the sound of a connected Allegretto audio distribution
system ON or OFF.
.
05-090-10 EN
15