General Information Concerning The Ce Marking - Hameg HM5510 Mode D'emploi

Hersteller
Manufacturer
Fabricant
Die HAMEG GmbH bescheinigt die Konformität für das Produkt
The HAMEG GmbH herewith declares conformity of the product
HAMEG GmbH déclare la conformite du produit
Bezeichnung / Product name / Designation:
Typ / Type / Type:
mit / with / avec:
Optionen / Options / Options:
mit den folgenden Bestimmungen / with applicable regulations /
avec les directives suivantes
EMV Richtlinie 89/336/EWG ergänzt durch 91/263/EWG, 92/31/EWG
EMC Directive 89/336/EEC amended by 91/263/EWG, 92/31/EEC
Directive EMC 89/336/CEE amendée par 91/263/EWG, 92/31/CEE
Niederspannungsrichtlinie 73/23/EWG ergänzt durch 93/68/EWG
Low-Voltage Equipment Directive 73/23/EEC amended by 93/68/EEC
Directive des equipements basse tension 73/23/CEE amendée par 93/68/CEE
Angewendete harmonisierte Normen / Harmonized standards applied /
Normes harmonisées utilisées
Sicherheit / Safety / Sécurité
EN 61010-1:2001 (IEC 61010-1:2001)

General information concerning the CE marking

HAMEG instruments fulfill the regulations of the EMC directive. The
conformity test made by HAMEG is based on the actual generic- and
product standards. In cases where different limit values are
applicable, HAMEG applies the severer standard. For emission the
limits for residential, commercial and light industry are applied.
Regarding the immunity (susceptibility) the limits for industrial
environment have been used.
The measuring- and data lines of the instrument have much influence
on emmission and immunity and therefore on meeting the acceptance
limits. For different applications the lines and/or cables used may
be different. For measurement operation the following hints and
conditions regarding emission and immunity should be observed:
1. Data cables
For the connection between instruments resp. their interfaces and
external devices, (computer, printer etc.) sufficiently screened cables
must be used. Without a special instruction in the manual for a
reduced cable length, the maximum cable length of a dataline must
be less than 3 meters and not be used outside buildings. If an interface
has several connectors only one connector must have a connection
to a cable.
Basically interconnections must have a double screening. For IEEE-
bus purposes the double screened cables HZ72S and HZ72L from
HAMEG are suitable.
2. Signal cables
Basically test leads for signal interconnection between test point and
instrument should be as short as possible. Without instruction in the
manual for a shorter length, signal lines must be less than 3 meters
and not be used outside buildings.
Signal lines must screened (coaxial cable - RG58/U). A proper ground
connection is required. In combination with signal generators double
screened cables (RG223/U, RG214/U) must be used.
22
Subject to change without notice
HAMEG GmbH KONFORMITÄTSERKLÄRUNG
Industriestraße 6 DECLARATION OF CONFORMITY
D-63533 Mainhausen DECLARATION DE CONFORMITE
Spektrum-Analysator/
Spectrum Analyzer/
Analyseur de spectre
HM5510 / HM55511
–
–
Messkategorie / Measuring category / Catégorie de mesure: I
Verschmutzungsgrad / Degree of pollution / Degré de pollution: 2
Elektromagnetische Verträglichkeit / Electromagnetic compatibility /
Compatibilité électromagnétique
EN 61326-1/A1 Störaussendung / Radiation / Emission:
Tabelle / table / tableau 4; Klasse / Class / Classe B.
Störfestigkeit / Immunity / Imunitee: Tabelle / table / tableau A1.
EN 61000-3-2/A14 Oberschwingungsströme / Harmonic current emissions /
Émissions de courant harmonique:
Klasse / Class / Classe D.
EN 61000-3-3 Spannungsschwankungen u. Flicker / Voltage fluctuations and
flicker / Fluctuations de tension et du flicker.
Datum /Date /Date
15. 07. 2004
3. Influence on measuring instruments
Under the presence of strong high frequency electric or magnetic
fields, even with careful setup of the measuring equipment an
influence of such signals is unavoidable.
This will not cause damage or put the instrument out of operation.
Small deviations of the measuring value (reading) exceeding the
instruments specifications may result from such conditions in
individual cases.
4. Noise immunity of spectrum analyzers
In the presence of strong electric or magnetic fields it is possible
that they may become visible together with the signal to be measured.
The methods of intrusion are many: via the mains, via the signal leads,
via control or interface leads or by direct radiation. Although the
spectrum analyzer has a metal housing there is the large crt opening
in the front panel where it is vulnerable. Parasitic signals may.
however, also intrude into the measuring object itself and from there
propagate into the spectrum analyzer.
HAMEG GmbH
Unterschrift / Signature /Signatur
Manuel Roth
Manager