Napoleon MADR1 Mode D'emploi page 8

8
Gas Hook-Up Instrucions
EN
WARNING!
occur.
Propane Cylinder Speciicaions
A dented or rusty cylinder may be hazardous and should be checked by your propane supplier. Never use a
cylinder with a damaged valve. The LP-gas supply cylinder must be constructed and marked in accordance
with the U.S. D.O.T. Speciicaions for LP-Gas Cylinders or the Standard for Cylinders, Spheres and Tubes for
Transportaion of Dangerous Good and Commission, CAN/CSA-B339, as applicable.
This appliance has been designed for use with a 20 lb. (9.1 kg) or 30 lb (13.6 kg) size propane cylinder only
(not supplied).
The LP-gas supply cylinder must be provided with a cylinder-connecion device compaible with the
connecion for the appliance. The propane cylinder must be provided with a shut-of valve terminaing in
a propane cylinder valve type QCC1, and a safety relief device having direct communicaion with the vapor
space of the cylinder. The cylinder supply system must be arranged for vapor withdrawal and the cylinder
shall include a collar to protect the cylinder valve. The LP-gas cylinder must be provided with a listed
overill protecion device (OPD). Do not store a spare LP-gas cylinder under or near this appliance. Never
ill the cylinder beyond 80 percent full.
Use only the pressure regulator and hose assembly provided with this appliance. Replacement pressure
regulators and hose assemblies must be speciied by the manufacturer. The regulator supplies a pressure
of 11 inches. water column to the appliance and has a QCC1 type iing. Cylinders to be used with this
unit must be supplied with a QCC1 cylinder valve. A QCC1 cylinder has a posiive seaing connecion,
which will not allow gas low unil a posiive seal has been achieved. It is also equipped with an excess
low device. In order to atain full low to the appliance, the valve must be in the of posiion when the
cylinder valve is turned on.
WARNING!
appliance.
LP (Propane) Gas
Atach cylinder retaining bracket to the base of the cylinder. Then secure to the surface to which it sits.
Cylinder should be on a level surface.
Cylinder Connecion: Ensure the gas regulator hose is kink free. Remove the cap or plug from the cylinder
fuel valve. Insert the black QCC1 regulator nipple onto the QCC1 fuel valve. Hand ighten clockwise. Do not
use tools. Leak test all joints prior to using the appliance. A leak test must be performed annually and
each ime a cylinder is hooked up or if a part of the gas system is replaced.
If this appliance is to be connected directly to a house propane gas supply line, follow the instrucions
for the natural gas hook-up.
CAUTION!
•
•
•
•
•
•
www.napoleongrills.com
If these instrucions are not followed exactly, a ire causing death or serious injury may
A ire will result if the gas supply hose makes contact with the underside of the
Make sure cylinder valve is in its full of posiion. (Turn clockwise to stop).
Check cylinder valve features to ensure it has proper external maing threads. (Cylinder Valve
Marked: USE WITH TYPE 1)
Inspect hose shipped with the unit for damage. Never atempt to use damaged or plugged
equipment. See your local LP Gas Dealer for repairs.
When connecing regulator assembly to the cylinder valve, hand ighten black QCC1 nut clockwise
to a posiive stop. DO NOT use a wrench to ighten. Use of a wrench may damage the quick closing
coupling nut and result in a hazardous condiion.
Locate the hose out of pathways where people may trip over it or in areas where the hose may be
subject to accidental damage.
Open cylinder valve fully (counter-clockwise). Turn the on/of valve at the unit slowly to the on
posiion and use a soapy water soluion to check all connecions for leaks as indicated in the
diagrams before atemping to light the appliance. If a leak is found, turn tank valve of and do not
use the appliance unil repairs can be made.