Sunex Tools SX243 Mode D'emploi page 4

Operating Instructions •
Air Supply...
Tools of this class operate on a wide range of air pressures.
It is recommended that air pressure of these tools measures
90 PSI at the tool while running free. Higher pressure (over
90 psig; 6.2 bar) raises performance beyond the rated
capacity of the tool which will shorten tool life because of
faster wear and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/or water
in the air line will cause damage to the tool. Drain the air tank
daily. Clean the air inlet filter screen on at least a weekly
schedule. The recommended hookup procedure can be
viewed in the above figure.
The air inlet used for connecting air supply, has stan-
dard 1/4" NPT. Line pressure should be increased to
compensate for unusually long air hoses (over 25 feet).
Minimum hose diameter should be 3/8" I.D. and fittings
should have the same inside dimensions and be tightly
secured.
Limited Warranty...
SUNEX INTERNATIONAL, INC. WARRANTS TO ITS CUSTOMERS THAT THE COMPANY'S SUNEX TOOLS
PRODUCTS ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will repair or replace its Sunex Tools
workmanship or materials, based upon the terms and conditions of the following described warranty plans attributed to that specific product.
This product carries a ONE-YEAR warranty. During this warranty period, Sunex Tools will repair or replace at our option any part or unit
which proves to be defective in material or workmanship.
Other important warranty information...
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover any repairs or
replacement made by anyone other than Sunex Tools or its authorized warranty service centers.The foregoing obligation is Sunex Tools' sole
liability under this or any implied warranty and under no circumstances shall we be liable for any incidental or consequential damages.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. Return equipment or parts to Sunex Tools, or an authorized warranty service center, transportation prepaid. Be
certain to include your name and address, evidence of the purchase date, and description of the suspected defect.
If you have any questions about warranty service, please write to Sunex Tools. This warranty gives you specific legal rights and you may also
have other rights which vary from state to state. Repair kits and replacement parts are available for many of Sunex Tools products regardless
of whether or not the product is still covered by a warranty plan.
Shipping Address: Sunex Tools • 315 Hawkins Rd. • Travelers Rest, SC 29690
Mailing Address: Sunex Tools • P.O. Box 4215 • Greenville, SC 29608
SX243
SX243om_111904.indd 4
Warning Information • Parts Breakdown
Lubrication...
Lubricate the air motor daily with quality air tool oil. If no
air line oiler is used, run a teaspoon of oil through the
tool. The oil can be squirted into the tool air inlet or into
the hose at the nearest connection to the air supply, then
run the tool.
Operation...
Always place a chisel in the hammer and hold the tool
down to the work before operating. Damage to the tool
or the retainer may result if this precaution is not followed.
The chisel retainers are not designed for complete safety
against accidental release of cutters or hammers. To avoid
injury, the throttle (trigger) must never be depressed unless
the chisel is held firmly against the work place. When tool
is not in actual use, the chisel must be removed. During
operation, safety goggles should ALWAYS be used to
guard against flying rust and chips. When using tool,
regulate the speed so that the chisel is not being driven
out of the cylinder. If piston is allowed to strike the cylinder
wall, internal damage will result.
branded products which fail to give satisfactory service due to defective
®
4
BRANDED
®
Rev. 11/19/04
11/19/04 2:58:06 PM