PRASTEL MRMINI2E+ Mode D'emploi page 2

MRMINI2E+
1. GENERAL INFORMATION
The receiver integrates the functions of receiver and decoder of standard and Rolling Code remotes with encrypted communication (SLIM+). Its memory is capable of memorizing up to 1000
different codes.
When the receiver is configured in encrypted mode, it accept only the remote with encrypted communication!
Intended use of the equipment: radio receiver in garage-door systems.
1. PROGRAMMING
Warning: the first registered remote is going to determine receiver functional mode, encrypted or not. If the first remote registered in memory is encrypted type (slim+), the
receiver will be set automatically on encrypted mode. Once the receiver set in encrypted mode it will accept only encrypted remote. If the receiver is set on standard mode, all
remotes are programmable in the memory, encrypted remote included (however their encrypted communication function will be disabled).
• Power up the receiver properly.
• Press button Prog.:
green led R1 and led blue light steadily indicating that programming is in progress for relay 1.
• To memorize remote button on relay 2, press again Prog. button: red led R2 and led blue light steadily indicating that programming is in progress on relay 2
• Carry out a transmission by pressing the channel button of the remote which should be memorized.
• The R1 or R2 led flashing confirms the memorizing of the button. The led returns to the fixed ignition state to report that it is possible to insert a new code. At the end led returns
steady lightening state, indicating that a new code can be entered.
• Memorise all the remote's button by carrying out a transmission with each one.
• To exit from memorizing process press Prog. button again. Exit from the process comes about automatically in any case 10 seconds after the last memorization.
2. TOTAL CANCELLATION OF MEMORY
This function allows to cancel all the memorized codes in the receiver memory and reset the functioning mode : standard or encrypted (return to configuration standby mode)
• Press and hold to Prog. button until the two led R1 and R2 starts flashing.
• Release the button.
• Press again Prog. button within 6 seconds to confirm cancellation. Confirmation is indicated by the led fast flashing frequency.
3. OUTPUT RELAY SELECTION
• Select the relay pressing Prog. each time to choose relay 1 (Led 2 : R1) or relay 2 (Led 3 : R2) .
• Change relay mode pressing and holding Prog. button until the led starts flashing:
3 fast flashing lights = monostable (1.5s)
3 slow flashing lights = bistable.
4. LED'S FUNCTIONNING
Led 1 – Blue
4 shorts
pulses
2 shorts pulses
1 shorts
pulses
ON
ON
ON
ON
ON
ON
DECLARATION OF CONFORMITY: Prastel declares that the following radio equipment: receiver MRMINI2E+ complies with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
6 fast flashing lights = monostable (6s)
6 slow flashing lights = timed bistable (1h)
Led 2 – Green
Relay 1
-
-
-
- 2 shorts pulses
- 1 long pulse
- OFF
ON
OFF
1 flash
OFF
Fast flashing
OFF
(Equivalent to the bistable mode but with an automatic shutdown of the relay after
=
one hour)
Led 3 – Red
Relay 2
- Waiting for settings
- Receiving only encrypted remotes
- Receiving all Prastel remotes
2 shorts pulses Receiving an unregistered code in memory
OFF Receiving an authorized code on Relay 1
1 long pulse Receiving an authorized code on Relay 2
OFF Current mode : Programming on Relay 1
ON Current mode : Programming on Relay 2
OFF Remote registered on Relay 1
1 flash Remote registered on Relay 2
OFF Remote already registered on Relay 1
Fast flashing Remote already registered on Relay 2
www.prastel.com
State
ISMRMINI2E+_EU_06_19