Jonsered LM2146C Li58-52 Manuel D'utilisation page 11

Basic cutting technique
• Always cut with a sharp blade for the best results. A
blade that is not sharp cuts unevenly and lets the
grass become yellow on the surface of the cut.
• Do not cut more than 1/3 of the length of the grass.
This specially applies during dry periods. Cut first
with the cutting height set high. Then examine the
result and lower to an applicable height. If the grass
is too long, operate slowly and cut two times if
necessary.
• For very heavy cutting, decrease the width of the cut
by making an overlap of the cut path and cutting
slowly.
• Cut in different directions each time to prevent
stripes in the lawn.
• Regularly hose the grass catcher with water and let
dry before use. Pores in cloth grass catchers can
become filled with dirt and dust with operation. The
grass catcher will then collect less grass.
Before you start the mower
• Keep persons and animals away from the work area.
• Do daily maintenance. See
12 .
To start the product
1. Put in the battery pack until you hear a click. Make
sure the battery pack is correctly installed. (Fig. 38 )
2. Put the key into the pocket below the battery lid.
Make sure the key is correctly installed. (Fig. 39 )
Note: The key can only be put in one direction.
3. Press the power button one time. The button
illuminates fully. (Fig. 40 )
4. Pull the motor control handle in the direction of the
handlebar. The power button starts to flash. (Fig.
41 )
5. Press the flashing power button. The product then
starts. (Fig. 42 )
To stop the product
• Release the motor control handle on the product, or
press the power button one time.(Fig. 43 )
To use the drive on the wheels (if
equipped)
(Fig. 44 )
• Pull the drive levers in the direction of the handlebar.
• Before you pull the product rearward, disengage the
drive and push the product forward approximately
10 cm.
• Release the drive levers to disengage the drive, for
example, when you go near an obstacle.
851 - 003 - 23.10.2018
MAINTENANCE on page
To empty the grass catcher
1. Lift the grass catcher with the frame handle.
2. Remove grass clippings from the grass catcher from
below the handle.
3. Empty grass clippings from the bag with the frame
handle and the bag handle.
CAUTION: Do not drag the bag when you
empty the grass catcher to prevent wear.
To change the cutting mode
The product can be changed to one of three different
cutting modes while in operation by pressing the cutting
mode button.
• Auto mode - The product automatically adjusts the
cutting speed of the product in response to the
quantity of grass being cut.
•
Note: The product is set to Auto mode by default
while in operation.
• Boost mode - The product operates at high speed
regardless of the quantity of grass being cut.
• While the product is in operation, press the
cutting mode button one time to change from
Auto mode to Boost mode. The cutting mode
button then illuminates.
• ECO mode - The product operates at low speed
regardless of the quantity of grass being cut.
• While the product is in operation, press the
cutting mode button one time to change from
Boost mode to ECO mode. The cutting mode
button then illuminates and flashes.
• To go back to the default Auto mode, press the
cutting mode button one time while the product is
in operation. The cutting mode button then stops
flashing.
Note: If the motor control handle is released during
operation, the product stays in the current cutting mode.
If the product automatically stops, or the operator
presses the power button, the cutting mode used before
is erased from memory and the product starts in Auto
mode when started again.
Battery status indication during
operation
The display on the user control interface shows the
battery capacity and if there are problems with the
battery pack. The battery capacity is shown while the
machine is in operation.
LED lights Battery status
All Green Fully Charged (100% - 76%)
LEDs come on
11