Monacor security VTM-10 Mode D'emploi page 8

4 Connection
GB
Always switch off the units to be connected before
connecting them!
1) Connect the video source to the input jack
COMPOSITE (5) or S-VIDEO (6). If different video
sources are connected to the two inputs, use the
OSD menu to switch from one to the other.
2) Connect the monitor to the jack MONITOR (8).
3) Connect the VGA output of a PC to the jack VGA (7)
if it is to be operated alternately with the converter
on a single monitor.
4) Connect the low voltage plug of the power supply
unit to the jack 5 V /500 mA (9) and the power
supply unit to a mains socket. Thus, the unit is
switched on; the POWER LED (1) will light up.
5 Operation
If the status LED CONVERSION (1) does not light up,
the signal of the input VGA is directly fed to the output
MONITOR (PC feed-through mode). This signal will
not be affected by any adjusting possibilities of the
converter.
1) Activate the converter with the button
status LED CONVERSION (1) will light up. Now the
converted video signal will be displayed on the
monitor. For a few seconds, information concerning
the input currently selected (COMPOSITE or
S-VIDEO) and the video standard of the signal
applied (PAL or NTSC) will be inserted in the picture.
If there is no signal at the input selected, "NO SIG-
NAL" will be inserted instead of the video standard.
Besides, the status LED SIGNAL (1) will not light up.
2) To switch between the two video inputs, call the
OSD menu (⇒ chapter 5.1).
3) To return to the PC feed-through mode, press the
button once again.
5.1 Settings in the OSD menu
Call the main menu in the converter mode with the but-
ton (2) or
than approx. 10 s with the OSD menu inserted, the
menu will automatically disappear.
The main menu:
––––––––––––––––––––––––
Picture
Input
Features
Resolution
Exit
Select the desired submenu with the button
(4) and call it with the button
To exit the main menu, select the item "Exit" and con-
firm with the button
8
(4). If no button is pressed for more
Main Menu
(3).
(or just wait for 10 seconds).
5.1.1 Submenu "Picture"
––––––––––––––––––––––––
Contrast
Brightness
Color
Tint
Save
To adjust Contrast, Brightness, Color, and Tint, se-
lect the corresponding function with the button
and then adjust the desired value: To increase the
value, press the button
press the button
immediately. A change of the tint value will only be
effective for NTSC signals.
To exit the submenu, select the menu item "Save" and
confirm with the button
5.1.2 Submenu "Input"
––––––––––––––––––––––––
(3). The COMPOSITE
S-VIDEO
Save
To select the video input, select the desired connection
with the button
The change will take effect immediately. The current
setting is highlighted in red.
To exit the submenu, select the menu item "Save" and
confirm with the button
5.1.3 Submenu "Features"
––––––––––––––––––––––––
OSD Mode
Sharpness
Motion
Motion Value
Save
Select the corresponding function with the button
then adjust the desired value with the buttons
. Any change will take effect immediately.
OSD Mode will define the type of insertion of the OSD
menu: with a white background covering the picture
(NOP or OR), with a transparent background (AND), or
with a negative picture section behind the menu inser-
tion (XOR).
With the function Sharpness activated (ON), the
contours of the video picture will be defined more
(2) or
clearly.
In case of fast movements in the video picture, the
function Motion allows to adjust a steady picture. With
the function activated (ON), the item Motion Value will
Picture
40
20
40
50
(4); to decrease the value,
(2). Any change will take effect
or .
Input
and confirm with the button
or .
Features
NOP
ON
ON
15
(3)
or .
;
and