Accessories - Black & Decker KA165GT Mode D'emploi

ENGLISH
Fitting sanding sheets (fig. A & B)
Detach the two diamond-shaped tips (11) from the
x
sanding sheet (12).
Hold the tool with the sanding base facing upwards.
x
Place the sanding sheet (12) onto the sanding base,
x
making sure that the holes in the sheet line up with the
holes in the base.
The diamond-shaped tip (11) can be reversed and replaced
when worn.
When the front part of the tip is worn, detach it from the
x
sheet, reverse it and press it onto the sanding base again.
When the whole tip is worn, remove it from the sanding
x
base and fit a new tip.
The polishing foam and pads (13) can be fitted the same
x
way as the sanding sheets.
Tip of the sanding base (fig. C)
When the sanding base tip (6) or tip holder (5) is worn, it can
be reversed or replaced. Spare parts are available from your
Black & Decker dealer.
Remove the screw (9).
x
Reverse or replace the worn part.
x
Fit and tighten the screw.
x
Finger attachment (fig. D)
The finger attachment is used for fine detail sanding.
Remove the screw (9).
x
Remove the diamond-shaped tip holder (5) from the
x
sanding base.
Fit the finger attachment (7) onto the sanding base.
x
Fit and tighten the screw.
x
Fit the appropiate sanding sheet (14) onto the finger
x
attachment.
Profile attachment (fig. E)
The profile attachment is used for contour sanding.
Remove the screw (9).
x
Remove the diamond-shaped tip holder (5) from the
x
sanding base.
Fit the profile attachment (8) onto the sanding base.
x
Fit and tighten the screw.
x
Fitting and removing a sanding profile (fig. F1 & F2)
Choose the sanding profile most suitable for your application.
x
Place one end of the sanding profile (10) into the recess at
x
the front end of the profile holder (8).
Push the other end of the sanding profile until it clicks
x
into place.
To remove the sanding profile, push it forward and pull
x
the rear end out of the profile holder (fig. F2).
6
Fitting a sanding sheet onto a sanding profile (fig. G)
Align the sanding sheet (15) with the sanding profile (10).
x
Press the sanding sheet onto the sanding profile, making
x
sure that the sanding sheet follows the shape of the profile.
Connecting a vacuum cleaner (fig. H)
The tool has an adaptor to connect it to a vacuum cleaner
when sanding wood. To connect the tool to a vacuum cleaner,
proceed as follows:
Fit the dust extraction connector (3) onto the adapter at
x
the back of the tool.
Connect the hose of a suitable vacuum cleaner to the
x
connector.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Do not cover the ventilation slots when using the
tool. Hold the tool as shown in fig. I. Make sure that the
sanding base is flat on the workpiece.
Switching on and off
To switch the tool on, set the on/off switch (1) to position I.
x
To switch the tool off, set the on/off switch to position O.
x

Accessories

The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Clear the cooling vents and slots with a clean, dry paint
x
brush.
Clean the housing with a clean, damp cloth. Do not use
x
solvents.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
x
Connect the brown lead to the live terminal in the new
x
plug.
Connect the blue lead to the neutral terminal.
x
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.