Foreword; Fireplace Characteristics; Description; Nominal Heat Output And Reduced Burn Rate Autonomy - deville C07335 Mode D'emploi

CAUTION CAUTION : : : : CAUTION CAUTION
TO PREVENT THE RISK OF FIRE, THIS FIREPLACE MUST BE INSTALLED IN ACCORDANCE
WITH ACCEPTED TRADE PRACTICES AND IN COMPLIANCE WITH THE TECHNICAL REGULATIONS
THE INSTALLATION OF THIS APPLIANCE MUST COMPLY WITH CURRENT D.T.U. (French Code of Practice)
INSTALLATION BY A QUALIFIED TRADESMAN IS RECOMMENDED.
We strongly recommend that you take the time to thoroughly read and familiarize yourself with this manual
in order to obtain maximum enjoyment and satisfaction from your DEVILLE fireplace.
All local, national, and european regulations must be respected when using this appliance.
The nonobservance of the assembly, installation and operating instructions shall engage the liability of the

1 - FOREWORD

•
The "ready to install" fireplaces, models are to be
installed in the same manner as a wood burning
stove. The rules for installation are identical,
particularly as regards the following points :
The type and installation requirements of the
-
chimney flue compatible with this usage.
The connection of the fireplace to the chimney
-
flue.
Room ventilation.
-
•
Chapter 4 specifically concerns the "ready to
install" fireplace :
Installation against a backing wall.
-
Height adjustment.
-
•
Important, the "Ready-to-Install" fireplaces do not
allow the connection of hot air outlet ducts: the
safety of the environment can no longer be
ensured if the screens which protect the backing
wall are modified (pierced, moved).
•
The following
recommendations for proper fireplace operation.
The building technical rules DTU 24-2-2 and 24.1
fully describe the specifications related to smoke
evacuation and fresh air intake requirements.
•
The ready-to-install fireplaces
C07342 comply with the French standards NF EN
13240.

2 - FIREPLACE CHARACTERISTICS

2.1 - Description

The "ready to install" fireplaces, models
exclusively wood-burning,
combustion, semi-open heating appliances, and are
designed to be installed against a backing wall
without any additional protection.
2.2 - Nominal heat output and reduced burn rate
autonomy
•
Nominal heat output in accordance with French
standard NF EN 13240 during the normal burn
rate test :
STIPULATED IN THIS MANUAL.
SPECIFICATIONS.
individual(s) concerned. The unit must not be modified.
chapters provide
C07335 and
grate-type continuous
C07335
C07342
Obtained with a draft of 12 Pa, and a wood
-
load of 10 kg for C07342, and 14 kg for model
C07335. Loads are comprised of 3 unsplit
hardwood logs.
The output indicated is the average output
-
obtained during this 3-hour test.
In order to obtain this output level, place on a
-
bed of approximately :
.
.
The air intake must be fully open.
•
An autonomy greater than 10 hours, at reduced
output, is obtained with a full load and by
completely closing the air inlet control.
2.3 - Description (Fig. 1)
basic
•
The fireplace consists of an insert, an exchanger
assembly and the trim. It is delivered in 2
packages.
•
The main elements which make up the insert are
identified in figure 1 :
The combustion chamber is made of 4 mm
-
thick steel and the back of the insert is
doubled with a cast iron hearth plate.
The door is of cast iron and fitted with seals
-
ensuring air-tightness.
The adjusting slide located on the lower
-
section of the door is used to set the burning
rate.
are
A secondary air inlet is built into the upper part
-
of the glass door to keep it clean and to
provide better combustion on the wood.
The ready-to-install fireplace C07342 is fitted
-
with a 2 speed electric fan, which speeds up
the convection around the hearth.
•
Net weight of the appliance :
14
Power Draft Mass discharge
rating of smoke
14 kW 12 Pa 10,5 g/s
10 kW 12 Pa 10,5 g/s
300 g of live coals, that is 3 cm thick for
C07342.
500 g, of live coals, that is 4 cm thick for
C07335.
C07335
C07342
Temperature
of smoke
321°C
299°C
140 kg
180 kg