Table des Matières
Publicité
Chapitre 10.0 Emplacement des détecteurs et plan d'évacuation
doivent être placés le plus près possible des chambres à coucher de l'habitation. Pour une protection
maximale, le détecteur de gaz CO doit aussi être placé à l'extérieur des chambres à coucher prin-
cipales ou à chaque étage de votre maison. La figure 5 montre les emplacements conseillés dans
l'habitation.
NE placez PAS les détecteurs de gaz CO dans les endroits suivants :
Où la température peut être inférieure à -10°C ou supérieure à 40°C
l
Près de vapeurs de solvants pour peinture
l
À moins de 1,5 m (5 pieds) d'appareils à flamme nue comme des fourneaux, des cui-
l
sinières et des foyers
Dans les flux d'échappement de moteurs à gaz, tuyaux d'aération, conduits de fumée ou de
l
cheminées
Ne le placez pas à proximité du tuyau d'échappement d'une automobile ; le détecteur s'en-
l
dommagera facilement
VEUILLEZ VOUS REPORTER AU FEUILLET D'INSTRUCTIONS DE
FONCTIONNEMENT ET D'INSTALLATION DU DÉTECTEUR DE GAZ CO POUR LES
CONSIGNES DE SÉCURITÉ ET LES MESURES EN CAS D'URGENCE.
10.0Regulatory Agency Statements
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment. This equipment has been tes-
ted and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Re-orient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: "How to Identify and Resolve Radio/Television Interference Problems". This booklet is available
from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.
The keypads represented in this manual can be used with the following Control Units: HS2016, HS2032, HS2064, HS2128.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules and, if the product was approved July 23, 2001 or later, the requirements adopted by the ACTA. On the side of
this equipment is a label that contains, among other information, a product identifier. If requested, this number must be provided to the Telephone Company.
HS2016 Product Identifier US:F53AL01BHS2128
HS2032 Product Identifier US:F53AL01BHS2128
HS2064 Product Identifier US:F53AL01BHS2128
HS2128 Product Identifier US:F53AL01BHS2128
USOC Jack: RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements
adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is
also compliant. See installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not rin-
ging in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total RENs, contact the local Telephone Company. For products approved after July 23, 2001, the REN for this product is part
of the product identifier that has the format US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For ear-
lier products, the REN is separately shown on the label.
Incidence of Harm
If this equipment (HS2016, HS2032, HS2064, HS2128) causes harm to the telephone network, the telephone company will notify you in advance that temporary dis-
continuance of service may be required. But if advance notice is not practical, the Telephone Company will notify the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the
Telephone Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment (HS2016, HS2032, HS2064, HS2128) for repair or warranty information, contact the facility indicated below. If-the equip-
ment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is solved. This equipment is
of a type that is not intended to be repaired by the end user.
DSC c/o APL Logistics 757 Douglas Hill Rd, Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for infor-
mation.
Alarm dialing equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (tele-
phone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialing equipment must be connected to a properly installed RJ-
- 38 -
Publicité
Table des Matières
