Panasonic EY37A2 Instructions D'utilisation page 12

3. Rotate the Tuning control to select either 12
EN
or 24 hour format. Press the Tuning control
to confirm your choice of clock format.
NOTE:
If the 12 hour clock format is chosen, the
radio will then use the 12 hour clock for
the setting of alarms and will display a
12 hour clock with PM indicator when in
standby mode.
Setting the clock time manually
1. Make sure the radio is powered on. Press
and hold the Tuning control knob to enter the
Advanced menu of the current mode.
2. Rotate the Tuning control until "CLK" shows
on the display and press the Tuning control
to enter the setting. Now the hour setting
begins flashing.
3. Rotate the Tuning control to select the
desired hour and press the Tuning control to
confirm the setting. Now the minute setting
begins flashing.
4. Rotate the Tuning control to select the
desired minute and press the Tuning control
to confirm the setting. The display will then
revert to the previous menu.
Setting the alarm clock
The radio has two alarms which can each be
set to wake you to AM/FM radio or buzzer
alarm. Ensure the clock time is set before
setting the alarms.
a. Setting radio alarm:
1. Make sure the radio is powered on.
2. Press and hold the radio alarm button, the
radio alarm symbol (
hour will flash followed by a beep.
3. When the hour digit flashes, rotate the
Tuning control to select the required alarm
hour and press the Tuning control to confirm
the hour setting.
4. Then rotate the Tuning control to select the
required alarm minute and press the Tuning
control to confirm the setting.
5. When radio alarm symbol is flashing, rotate
Tuning control to select desired wake-up
band and station, then press Tuning control
to confirm the selection.
6. Rotate Tuning control to select the desired
volume and press Tuning control to confirm
the setting. Radio alarm setting is now
completed.
NOTE:
If the selected AM/FM alarm station is not
available when the alarm is sounding, the
buzzer alarm will be used instead.
EY37A2.indb 12
b. Setting HWS (Humane Wake System)
1. Make sure the radio is powered on.
2. Press and hold the buzzer alarm button, the
3. When the hour digit flashes, rotate the
–––––– CLK
4. Then rotate the Tuning control to select the
5. Rotate Tuning control to select the desired
When the alarm sound
Disabling/cancelling alarms
Alarm sound duration ––––––––––––– ALM
1. Press and hold the Tuning control to enter
2. Rotate the Tuning control until "ALM" shows
3. Rotate the Tuning control to cycle through
) and the display
Snooze ––––––––––––––––––––––––– SNZ
1. When the alarm sounds, press any button
2. To adjust the silence time for the snooze
3. Rotate the Tuning control until "SNZ"
4. To cancel the snooze timer while the alarm
- 12 -
buzzer alarm:
buzzer alarm symbol (
hour will flash followed by a beep.
Tuning control to select the required alarm
hour and press the Tuning control to confirm
the hour setting.
required alarm minute and press the Tuning
control to confirm the setting.
volume and press Tuning control to confirm
the volume. Buzzer alarm setting is now
completed.
To cancel a sounding alarm, press the Power
button.
To disable an active alarm, press the
corresponding alarm button to cancel the
alarm setting.
the advanced menu of the current mode.
on the display. Press the Tuning control to
enter the setting.
the option of 1, 3, 5, 10, 15, 30 and 60
minutes. Stop when the desired option
appears on the display, then press the
Tuning control to confirm the setting.
other than the Power button will silence the
alarm. Snooze symbol (
the display.
timer, press and hold the Tuning control to
enter the menu setting.
appears on the display, then press the
Tuning control to enter the setting. Rotate the
Tuning control to adjust the silence time from
the options of 1, 3, 5, 10, 15 minutes or OFF
for the snooze timer.
is suspended, press the Power button.
) and the display
) will appear on
2015-2-13 9:53:17