Important - Kindcomfort SAVILEV8A Notice D'instruction

5. Loosen the harness buckle, lift the covers of both the base and
the back of the seat and pass the waist belt under both covers,
and install the vehicle vertical safety belt passing it through guide
R (3.6 and 3.7).
6. Tighten the lap belt and diagonal shoulder belt, then place the red
safety clip on the diagonal shoulder belt tongue as near to the
vehicle anchor point as possible without touching it! (3.8, 3.9 y
3.10).
7. To unfasten the harness press the red button on the buckle
downwards (3.11).
8. For greater space and to loosen the harness, it is necessary to
press the harness adjustment button, while simultaneously
pulling the harness straps down with your other hand (do not pull
the harness protector) (3.12). Place the head support in its lowest
position (3.13).
9. Place the child in the child car safety seat (3.14)
10. Join the 2 buckle metal connectors, pass both connectors through
the slot in the upper part of the buckle until you hear a "click"(3.15).
11. Check that the harness straps lie firmly on the child's chest; the
harness must be adjusted by pressing the harness adjustment
button. The harness should not be twisted. Press the metal button
that is located between the child's legs and then pull the straps
until the child is properly secured and a correct height (3.16 and
3.17).
12. Remove cushion 1 and Group 0+
I, II and III. (3:18).
4. INSTALLING CHILD SEAT. GROUP 1.
WARNING
Installing the child seat forward facing can only be maid if the child
is more than 9 kg.
1. Fit this child seat into the vehicle´s seat, making sure it is firmly
pressed against the vehicle seat backrest (4.1).
2. Raise the backrest cover and insert the safety belt through red
waist belt guides B. Pass the waist belt through both red guides at
the base of the seat (4.2).
24 Child restraint system
2 base to use the seat with groups
Only suitable for Group 1, approx.
9 months to 4 years (9-18 Kg.)
3. Check that the seat belt of the vehicle is passed through the
safety guides and that the belts are not twisted. Insert the safety
seat belt in the vehicle anchor point and press until you hear a
"click" so that the child seat is properly installed (4.3).
4. Tighten the lap belt and diagonal shoulder belt, then place the red
safety clip on the diagonal shoulder belt tongue as near to the
vehicle anchor point as possible without touching it! (3.8, 3.9 y
3.10).
5. To unfasten the harness press the red button on the buckle
downwards (4.7).
6. For greater space and to loosen the harness, it is necessary to
press K
the harness straps towards you with your other hand (do not pull
the harness protector) (4.8).
7. To recline the seat, pull red seat reclining handle
towards you until the desired position is obtained (4.9).
8. Place the child in the child car safety seat(4.10).
9. Adjust the head support, press headrest adjustment handle
move it up and down until the desired position is obtained (4.11).
10. Adjust the width of the child seat by turning the adjustment knob
of the G
size of your child by turning the knob (4.12).
11. Join harness tape buckles in buckle-holder, insert both buckles in
child seat buckle-holder and press until you hear a "click" (4.11).
12. Pull harness straps down to ensure both the vehicle belts properly
secure the child seat (4.15).
13. The harness straps should lie comfortably on the child, without
too much slack. It should lie gently on the child without exerting
pressure or causing damage and the child should not be obliged to
assume a bad posture.
Always check that the harness straps are suitable for the height of
your child. The shoulders of the child should always be just below the
back slots at a suitable height (4.16).
KM0123 Group 0+/1/2/3
harness adjustment button, while simultaneously pulling
laterals and adapt the width of the seat according to the

IMPORTANT

EN
M and pull the base
Q and
www.kindcomfort.com 25