Shutting Down - Anselmo Cola ANTIGUA Manuel D'installation, D'utilisation Et D'entretien

4.5 Shutting down

To turn off the stove, press button P4 for a few seconds. The auger is immediately stopped and the fume exhaust
fan goes to high speed, with the message FINAL CLEANING appearing on the display. The fume exhaust and air
ventilation motors will remain on until the stove temperature has fallen sufficiently.
At the end of the operation the message OFF will appear on the display.
During the shutdown phase the stove cannot be restarted until the fume temperature has dropped below a fixed
value for a given time. If the activation button is pressed the message WAITING COOL will be displayed.
4.6 Menu
Press button P3 to access the menu. It is divided into eleven sub-menus for accessing the settings of the electronic
control. The various sub-menus can be scrolled by pressing buttons P1 and P2, and can be accessed by pressing
button P3 and exited by pressing P4.
4.6.1 Menu 01 – adjust fans
To set the hot air flow manually, the fan speed can be selected by choosing a value of 1 to 5; whereas for the fan
speed to be automatic and follow the selected power, choose the value A.
4.6.2 Menu 02 – set clock
Before operating with the stove the current time and date must be set in order to have a reference for possible
chrono programming.The electronic control device has a lithium battery mod. CR2032 of 3 Volt inside. It allows the
internal clock with own autonomy if the clock does not keep the time with stove not powered or a series of zeros
appears at restart, battery replacement is necessary: call an authorised service centre.
To set the clock, access the menu by pressing P3 and adjust the time with buttons P1 and P2. Press P3 again to
adjust the minutes, day, month and year.
–
4.6.3 Menu 03 enable chrono
For enabling all chrono functions. To enable the chrono, access the first sub-menu ENABLE CHRONO and set it to
ON with buttons P1 or P2. The corresponding symbol lights up on the display and programming is active. The
manual controls of the panel and the remote control retain priority with programming.
Access the second sub-menu DAY PROGRAM to enable or disable the daily chrono with buttons P1 and P2. Then
press button P3 to set up to two operation phases delimited by the set times.
Access the third sub-menu WEEK PROGRAM to enable, disable and set the functions of the weekly chrono. Follow
the same procedures of the previous paragraph. Up to four operation phases delimited by the set times and days
can be set.
Do the programming carefully, without overlapping the activation and/or deactivation times on the same
day in different programs.
Access the fourth sub-men WEEKEND PROGRAM to enable, disable and set the chrono functions for the weekend.
Follow the same procedures of the previous paragraph. Up to two operation phases delimited by the set times can
be set.
To avoid unwanted startup and shutdown operations, activate only one program at a time.
4.6.4 Menu 04 – select language
With this selection it is possible to set the desired language from those available.
4.6.5 Menu 05 – standby mode
By selecting ON in STANDBY mode the corresponding symbol on the display lights up and the stove shuts down
automatically when the room temperature T has reached the set value (Tset + ΔT) for a given time.
The next restart in automatic will be possible only when the room temperature falls below the set value by a few
degrees and precisely (Tset - ΔT) where ΔT default = 2°C.
With the OFF selection, the modulation function is active but not the STANDBY mode. Therefore when the
temperature exceeds the set value the stove will operate at minimum power.
4.6.6 Menu 06 – buzzer
With this selection it is possible to activate or deactivate the stove alarm buzzer.
4.6.7 Menu 07 – initial loading
Allows the preloading of pellets for a given time. This function can only be activated when the stove is off and cold
and is used if the auger is empty due to no more pellets. It is started with button P1 and stops with button P4.
35 ANTIGUA