Ravelli Infinity Plus 11 C Manuel D'utilisation Et D'entretien page 68

Rev.1 12/04/2018
Pag.68
EN
START/RESTART WAIT START/RESTART WAIT
SWITCH ON RESTART SWITCH ON RESTART
HOT SMOKE HOT SMOKE
OFF OFF
WAIT FOR PELLETS WAIT FOR PELLETS
OUT OF OUT OF
INFEED SCREW INFEED SCREW
OVERFLOW OVERFLOW
GENERIC ALARM GENERIC ALARM
ANOMALY (general) ANOMALY (general)
AUTOMATIC CLEANING AUTOMATIC CLEANING
SYSTEM ACTIVE SYSTEM ACTIVE
Warning Pop -Up Warning Pop -Up
ANOMALY ANOMALY
SERVICE REQUEST SERVICE REQUEST
Alarms (table with reference codes) Alarms (table with reference codes)
TITLE TITLE
AL 01 AL 01 BLACK OUT BLACK OUT
AL 02 AL 02 K PROBE K PROBE
FAILURE FAILURE
AL 03 AL 03 OVERTEMP. K OVERTEMP. K
Use and maintenance manual Infinity Plus 11
Switch-on is requested but with the stove in cooling phase; once this condition is Switch-on is requested but with the stove in cooling phase; once this condition is
met, it restarts automatically. met, it restarts automatically.
The HOT restart phase is activated. The HOT restart phase is activated.
Functioning is similar to the SWITCH ON phase Functioning is similar to the SWITCH ON phase
The maximum fume temperature threshold has been reached. To facilitate cooling, The maximum fume temperature threshold has been reached. To facilitate cooling,
the stove brings the capacity to a minimum with ventilation at power level 5, leading the stove brings the capacity to a minimum with ventilation at power level 5, leading
to a decrease in fume temperature. to a decrease in fume temperature.
The stove is off The stove is off
When the switch-on request from ECO-STOP mode coincides with an automatic When the switch-on request from ECO-STOP mode coincides with an automatic
switch-off condition (from the TIMER), the stove turns on ensuring total cleaning of switch-off condition (from the TIMER), the stove turns on ensuring total cleaning of
the brazier before switching to FINAL CLEANING. the brazier before switching to FINAL CLEANING.
CONDITION: when the pellet setting (set pellets +5) is near the continuous load CONDITION: when the pellet setting (set pellets +5) is near the continuous load
condition. condition.
SOLUTION: Set the value back to 0. SOLUTION: Set the value back to 0.
The stove is in alarm state; refer to the troubleshooting chapter. The stove is in alarm state; refer to the troubleshooting chapter.
The stove has detected an anomaly; refer to the troubleshooting chapter. The stove has detected an anomaly; refer to the troubleshooting chapter.
For models with automatic cleaning system it indicates the operating state of the For models with automatic cleaning system it indicates the operating state of the
same. same.
DESCRIPTION DESCRIPTION
The threshold value of set work hours has been reached. The symbol displayed The threshold value of set work hours has been reached. The symbol displayed
remains active throughout the work phase. Non-routine maintenance is required remains active throughout the work phase. Non-routine maintenance is required
on the stove. on the stove.
REASON REASON
No voltage during work phase No voltage during work phase
The K probe is malfunctioning The K probe is malfunctioning
The K probe is disconnected from the The K probe is disconnected from the
electronicboard electronicboard
Combustion in the brazier is not optimal due to Combustion in the brazier is not optimal due to
clogging or obstructions of internal stove ducts clogging or obstructions of internal stove ducts
inside the stove inside the stove
SOLUTION SOLUTION
Press the switch off key and switch on the stove Press the switch off key and switch on the stove
again again
If the problem persists, contact the Support If the problem persists, contact the Support
Service Service
Contact the Support Service Contact the Support Service
Contact the Support Service Contact the Support Service
Switch off the stove, clean the brazier and the Switch off the stove, clean the brazier and the
tube bundle and adjust the combustion setting the tube bundle and adjust the combustion setting the
Pellet/Air values Pellet/Air values
Contact the Support Service Contact the Support Service