VONROC MS504AC Traduction De La Notice Originale page 14

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 48
EN
In this case the machine must be secured to the
sub frame with bolts. Use the four holes (12) to
do this. The sub frame must be anchored with 4
bolts to the floor plate with dimensions of at least
1 square meter. Mount the power tool on the saw
stand in the transport position.
3. Flexible installation
This type of installation is not recom-
mended by the manufacturer.
If, in exceptional circumstances, it is not possible
to mount the power tool on a flat and stable work
surface, you can improvise by setting it up with the
tilt protectors.
Without the tilt protector, the power tool will
not be stable and can tip over especially when
sawing maximum mitre and/or bevel angles.
• The rear tilt protector is fixed onto the base of
the machine and cannot be adjusted.
• Rotate the front tilt protector (37) inwards or
outwards as shown on figure F until the power
tool is positioned level on the work surface.
Checking the protective guard (fig. A)
The Retracting protective guard (5) protects
against accidental contact with the saw blade and
from saw chips flying around. Before use, it must
be checked if the saw blade guard is functioning
correctly. To do so, pull the handle (2) downwards
and check the following:
• The Retracting protective guard (5) must provide
access to the saw blade (6) without getting in
contact with other parts.
• When folding the saw upwards into the starting
position, the Retracting protective guard (5) must
cover the entire saw blade (6) automatically.
Replacing the saw blade (fig. G)
Before carrying out any work on the
machine, disconnect the mains plug from
the power supply.
When mounting the saw blade, wear
protective gloves. Danger of injury when
touching the saw blade.
14
Only use saw blades that correspond with
the characteristic data given in the operating
instructions. Use only saw blades that are
marked with a speed equal or higher than
the speed marked on the machine.
Do not under any circumstances use
grinding discs as the cutting tool.
Before replacing the saw blade, it is strongly ad-
vised to set the mitre angle and bevel angle to 0°.
Otherwise, access could be limited.
Removing the saw blade
1. Lock the saw in upwards position by using the
position lock knob (38);
2. Loosen the retaining bolt (40) using a philips
headed screwdriver as shown on figure G1;
WARNING! Do not fully remove the retaining bolt
(40), only loosen it.
3. Fold the retracting protective guard (5) upwards
until the clamping bolt (42) can be accessed
freely, as shown on figure G2;
4. Insert the hex key into the clamping bolt (42).
The retracting protective guard (5) can be
released, it will fold onto the hex key.
5. Turn the clamping bolt (42) with the hex key
(34) and at the same time press the spindle
lock (43) until it engages.
6. Firmly hold the spindle lock (43) and loosen the
clamping bolt (42) by turning it clockwise (left-
hand thread).
7. Remove the clamping bolt (42) and clamping
flange (41). Afterwards, the saw blade (6) can
be removed.
Mounting the saw blade
When fitting the saw blade, make sure that
the cutting direction of the teeth (arrow
direction on the saw blade) matches the
direction of the arrow on the guard (4).
When fitting the saw blade (6), check to see
that it turns freely in the kerf plate (13) in
both 0° and 45° angle settings.
1. Clean the saw blade and all clamping parts to
be assembled.
2. Loosen the retaining bolt (40) using a philips
headed screwdriver as shown on figure G1;
WARNING! Do not fully remove the retaining bolt
WWW.VONROC.COM

Publicité

Table des Matières
loading

Table des Matières