Panasonic TY-TBN03G Mode D'emploi page 13

Plaque à bornes 3g-sdi avec son
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 32
3
Attach the terminal display
label.
Remove the separator on the
back of the terminal display
label (included) and attach it
on the back of the main unit.
Check carefully if the
attaching position and
direction are correct.
Video/Audio signals supported by this terminal board
For projector
Please refer to the operating instructions of the projector.
For flat panel display
The format chart below shows the supported format of the flat panel display LQ series.
Single, Dual and Quad on the Interface mean as follows.
Single: Independent input for SDI1 or SDI2 of SLOT1, or SDI3 or SDI4 of SLOT2
Dual: Input combining SDI1 with SDI2 of SLOT1, or combining SDI3 with SDI4 of SLOT2
Quad: Input combining all SDI1 and SDI2 of SLOT1, and SDI3 and SDI4 of SLOT2
Supported SDI input signal format chart
Interface
Format
(Single /
Dual / Quad)
Single
SD (525 / 59.94i)
Single
SD (625 / 50i)
Single
1 280 x 720 / 50p
Single
1 280 x 720 / 60p *
Single
1 920 x 1 080 / 24PsF *
Single
1 920 x 1 080 / 25PsF
Single
1 920 x 1 080 / 30PsF *
Single
1 920 x 1 080 / 50i
Single
1 920 x 1 080 / 60i *
Single
1 920 x 1 080 / 24p *
Single
1 920 x 1 080 / 25p
4K division
(1.5G HD-SDI /
(SQUARE /
3G Level A /
INTERLEAVE)
3G Level B-DL /
3G Level B-DS)
1.5G HD-SDI
3G Level A /
3G Level B-DL
1.5G HD-SDI
3G Level A /
1
3G Level B-DL
1.5G HD-SDI
1
3G Level A /
3G Level B-DL
1.5G HD-SDI
3G Level A /
3G Level B-DL
1.5G HD-SDI
1
3G Level A /
3G Level B-DL
1.5G HD-SDI
3G Level A /
3G Level B-DL
1.5G HD-SDI
1
3G Level A /
3G Level B-DL
1.5G HD-SDI
1
3G Level A /
3G Level B-DL
1.5G HD-SDI
3G Level A /
3G Level B-DL
Note
Attach the terminal display label next to the SLOT
display label by aligning the upper left corner of
terminal display label with the upper right corner of
SLOT display label attached on the rear of display
unit.
When replacing another terminal board with this
terminal board, the customer shall keep the replaced
terminal board for future repair or servicing.
SDI mode
Sampling
structure
(4:2:2 / 4:4:4)
422
422
422
422
422
422
422
422
422
422
422
422
422
422
422
422
422
422
Bit depth
Colour space
(8 bit / 10 bit /
(YC
C
/ RGB /
B
R
12 bit)
XYZ)
8 / 10
YC
C
B
R
8 / 10
YC
C
B
R
8 / 10
YC
C
B
R
444
8 / 10
YC
C
/ RGB
B
R
8 / 10
YC
C
B
R
444
8 / 10
YC
C
/ RGB
B
R
8 / 10
YC
C
B
R
12
YC
C
B
R
444
8 / 10 / 12
YC
C
/ RGB
B
R
8 / 10
YC
C
B
R
12
YC
C
B
R
444
8 / 10 / 12
YC
C
/ RGB
B
R
8 / 10
YC
C
B
R
12
YC
C
B
R
444
10 / 12
YC
C
/ RGB
B
R
8 / 10
YC
C
B
R
12
YC
C
B
R
444
8 / 10 / 12
YC
C
/ RGB
B
R
8 / 10
YC
C
B
R
12
YC
C
B
R
444
8 / 10 / 12
YC
C
/ RGB
B
R
8 / 10
YC
C
B
R
12
YC
C
B
R
444
8 / 10 / 12
YC
C
/ RGB
B
R
8 / 10
YC
C
B
R
12
YC
C
B
R
444
8 / 10 / 12
YC
C
/ RGB
B
R
13
English

Publicité

Table des Matières
loading

Table des Matières