Cleaning And Maintenance - Dometic Club/Ace AIR Pro Extensions Notice D'utilisation

Masquer les pouces Voir aussi pour Club/Ace AIR Pro Extensions:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 13
Using the extension
!
CAUTION! Risk of injury and material damage
Never open the zipper on the protective sleeve while an air
pole is inflated. This will result in the air pole bursting.
Before first use
Familiarize yourself with the product by carrying out a test set up before
the product is used for the first time. Check if the scope of delivery is
complete.
Choosing a site
Choose a flat site that is protected from wind:
1. If necessary, use a windbreak.
2. Choose a shaded site to avoid UV degradation of the fabric.
3. Avoid pitching under trees as falling branches, resin, etc. can damage
the product.
4. Clear the site of sharp stones and debris to avoid damaging the
groundsheet.
5. Set up the product with the doors facing away from the wind.
Setting up the extension
!
CAUTION! Risk of injury and material damage
Only attach the extension to an awning tent that is
mounted into a fixed rail not into a cassette awning.
Do not use any type of compressor designed to inflate
car tires.
Only inflate the air poles into the green zone of the
pressure gauge of the hand pump supplied with the
awning tent (9 psi/0.62 bar).
A
NOTICE! Material damage
Do not open or close the zippers by force.
I
NOTE
The extension comes with heavy duty pegs. These will
be suitable for many sites but for some types of ground
special pegs will be needed. Ask your dealer.
Drive the pegs at a 45° angle away from the extension
into the ground.
Peg each guy line in-line with the seam it starts from.
Keep the following tips in mind while setting up the extension:
The figures provide a general overview of the set-up. The actual set-up
will vary slightly based on the model of awning tent and extension.
Get help. The set-up is easier with more people.
After standing the extension upright, check the corner pegs and
re-peg if necessary. The base of the awning tent should be taut and in
a rectangular shape.
Peg the guy lines so that the extension is under tension without distort-
ing the shape.
Check the guy lines from time to time to ensure adequate tension, if
necessary use the runners to adjust.
Set up the extension as follows:
1. To protect the extension from dirt and damage, lay down a ground-
sheet or footprint before unpacking.
2. Unpack the extension.
3. Separate and identify the different components.
4. Ensure the awning tent is completely pegged.
5. Deflate the awning tent partially before attaching the extension.
EN
6. Re-inflate the awning tent before pegging out the extension.
7. Proceed as shown to set up the extension (fig. 1, page 3 to fig. e,
page 5).
Dismantling the extension
A
NOTICE! Material damage
Do not use force when dismantling the extension. Other-
wise you might damage any material.
1. Remove any dirt on the outside.
2. Close all window blinds.
3. Close all doors.
4. Remove all lines and straps.
5. Remove all pegs between the corner pegs.
6. Open the outlet valves.
7. Wait until most of the air has been expelled.
8. Remove the four corner pegs.
9. Fold/roll the extension towards the valve to expel more air.
10. When deflated, roll the extension to fit into the carry bag.
11. Ensure that all parts are clean before packing them into the carry bag.
12. If the extension is wet or damp, dry fully as soon as possible.

Cleaning and maintenance

A
NOTICE! Damage hazard
Do not use sharp or hard objects or cleaning agents for
cleaning.
Do not use alcohol based materials, chemicals, soap
and detergents for cleaning.
Remove bird droppings and tree resin as soon as
possible to avoid permanent damage to the material.
1. If necessary, clean the product with clean water and a soft brush.
2. Apply impregnation against water and UV radiation before each trip.
Storing the extension
I
NOTE
Fully set up the extension for cleaning.
Choose a sunny day for cleaning to ensure the material
will dry thoroughly.
1. Clean the extension.
2. Air fully and ensure the extension is totally dry before packing away.
3. Store in a well ventilated dry place.
4445103215
7

Publicité

Table des Matières
loading

Table des Matières