Lamp Replacement; Overhead Rigging - BEGLEC Wild Tech Mode D'emploi

ENGLISH
LAMP (RE)PLACEMENT
In case of replacement of the lamp or maintenance, do not open the fixture within 10
minutes until the unit cools down after switching off. Always unplug the unit before
servicing! Always use the same type of spare parts (bulbs, fuses, etc.) When
replacing parts, please only genuine spare parts.
• Unplug the mains cable.
• Wait for about 10 minutes until the unit has been cooled down.
• Unscrew the knob that closes the lamp compartment of the fixture
and open de top of the enclosure.
• On the inside you will see the lamp socket. Tear the lamp socket
gently out of the lamp compartment.
• Unplug the old lamp. Hold the lamp socket while unplugging the
lamp instead of pulling the cable!
• Hold the lamp socket while pressing the new lamp gently in the
socket.
Attention! Check the label on the backside of the device or see
the technical specifications in this manual to know which lamp
should be used. Never install lamps with a higher wattage! Lamps
with higher wattage generate temperatures the device was not
designed for. If the device uses a lamp transformer, it will burn due
to current overload.
• Don't touch the bulb with bare hands! This drastically shortens the
lifespan of the lamp. If you touched the lamp, clean it with a cloth
and a little denatured alcohol. Wipe the lamp off before installing.
• Put the new lamp back inside the unit. Be sure that the wires don't touch the lamp.
• Close the lamp compartment.
• Done!
EXCHANGING A GOBO
The logo projector accepts both metal and glass gobos.
Diameter: 53.3mm (D-size) maximum thickness glass gobos: 3mm
• Switch off the main supply and unplug the unit.
• Unscrew the small knob (8) on the bottom of the enclosure to open the gobo compartment.
• Remove the fixation ring of the gobo. You can do this easily with your
fingers.
• Remove the gobo and insert the new gobo.
• Press the fixation-ring together and insert it in front of the gobo.
• Make sure that the end of the fixation ring locks in the groove of the gobo
holder.
• Close the gobo compartment again.
• Done!
JB SYSTEMS®
OPERATION MANUAL
3/26 LOGO PROJECTOR
ENGLISH

OVERHEAD RIGGING

Best installation distance:
A projection distance of +/- 5 meters from the wall is perfect.
From this distance the projection will cover an area of 2.1m x
2.1m.
• Important: The installation must be carried out by
qualified service personal only. Improper installation
can result in serious injuries and/or damage to property.
Overhead rigging requires extensive
Working load limits should be respected, certified
installation materials should be used, the installed device should be inspected regularly for safety.
• Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
• Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
• The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
• Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
• Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
• The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
• Don't cover any ventilation openings as this may result in overheating.
• The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
OPERATING INSTRUCTIONS
• Once connected to the mains the device starts running.
• Point the projector to the wall and adjust the focus to
obtain a clear picture.
• Eventually adjust the rotating speed and/or direction of the
gobo with the dip switches on the back of the unit (5):
o DIP1 8: slow to fast rotation speed.
o DIP9: Rotation direction (left or right)
o DIP10: Rotation on/off switch
• Regular breaks during operation are essential to maximize
the life of this device as it is not designed for continual
use.
• Do not switch the unit on and off in short time intervals as
this reduces the lamp life.
• The units' surface temperature may reach up to 85°C.
Don't touch the housing with bare-hands during its
operation.
• Always unplug the unit when it is not used for a longer
time or before replacing the bulb or start servicing.
• In the event of serious operating problems, stop using the
fixture and contact your dealer immediately.
• Important: Never look directly into the light source! Don't
use the effect in the presence of persons suffering from
epilepsy.
JB SYSTEMS®
OPERATION MANUAL
experience!
4/26 LOGO PROJECTOR