DeWalt DCN650 Guide D'utilisation page 5

into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could result
in a hazardous situation.
5) Battery Tool Use and Care
a ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
b ) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c ) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws, or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
d ) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
6) Service
a ) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Nailer Safety Warnings
• Always assume that the tool contains fasteners.
Careless handling of the tacker can result in unexpected
firing of fasteners and personal injury.
• Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the fastener
causing an injury.
Do not actuate the tool unless its placed firmly
•
against the workpiece. If the tool is not in contact with
the workpiece, the fastener may be deflected away from
your target.
• Disconnect the tool from the power source when the
fastener jams in the tool. While removing a jammed
fastener, the tacker may be accidentally activated if it is
plugged in.
• Do not use the tacker for fastening electrical cables.
It is not designed for installation and may damage the
insulation of electric cables thereby causing electric shock
or fire hazards.
Additional Nailer Safety Warnings

WARNING: When using any nailer, all safety
precautions, as outlined below, should be followed
to avoid the risk of death or serious injury. Read and
understand all instructions before operating the tool.

WARNING: NEVER spray or in any other way apply
lubricants or cleaning solvents inside the tool. This can
seriously affect the life and performance of the tool.
• Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring. Contact with a "live" wire
will make exposed metal parts of the tool "live" and shock
the operator.
• Actuating tool may result in flying debris, collation
material, or dust which could harm operator's
eyes. Operator and others in work area MUST wear
safety glasses with side shields. These safety glasses
must conform to ANSI Z87.1 requirements (approved
glasses have "Z87" printed or stamped on them. It is
the employer's responsibility to enforce the use of eye
protection equipment by the tool operator and other
people in the work area.
• Always wear appropriate personal hearing and
other protection during use. Under some conditions
and duration of use, noise from this product may
contribute to hearing loss.
• Disconnect battery pack from the tool when not in
use. Always remove battery pack and remove fasteners
from magazine before leaving the area or passing the
tool to another operator. Do not carry tool to another
work area in which changing location involves the use
of scaffoldings, stairs, ladders, and the like, with battery
pack connected. Do not make adjustments, perform
maintenance or clear jammed fasteners while battery is
in place.
• Do not remove, tamper with, or otherwise cause
the tool, trigger, trigger lock-off, or contact trip to
become inoperable. Do not tape or tie trigger or contact
trip in the on position. Do not remove spring from contact
trip. Make daily inspections for free movement of trigger
and contact trip. Uncontrolled discharge could result.
• Inspect tool before use. Do not operate a tool if any
portion of the tool, trigger, trigger lock-off, or
contact trip is inoperable, disconnected, altered, or
not working properly. Damaged parts or missing parts
should be repaired or replaced before use. Refer to Repairs.
• Do not alter or modify the tool in any way.
• Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control. When tool is not in use, it should be locked in
a safe place, out of the reach of children.
Do not carry the tool from place to place holding the
•
trigger. Accidental discharge could result.
• Always use trigger lock-off when tool is not in
immediate use. Using the trigger lock-off will prevent
accidental discharge.
• Do not overreach. Maintain proper footing and balance
at all times. Loss of balance may cause personal injury.
Use the tool only for its intended use. Do not
•
discharge fasteners into open air, concrete, stone,
extremely hard woods, knots or any material too
hard for the fastener to penetrate. Do not use the
body of the tool or top cap as a hammer. Discharged
English
3