Siemens DO05705 Notice De Montage Et D'utilisation page 11

Congratulations on purchasing this Siemens appliance. You
have acquired a top-quality product, which will give you a lot
of enjoyment.
Please read this installation and operating instruction
manual carefully, then act accordingly! Store for future
reference.
Installation instructions
Unpacking
Inspect the new appliance for transport damage!
Please dispose of the packaging, and if applicable, the old
appliance in an environmentally-friendly manner.
Scope of delivery
I.
1 Appliance with operating panel
2 Installation bracket
3 DO3170D5, DO3175D5 and DO3185D5 only:
Mounting (2 screws, 2 wall plugs)
4 Documentation
5 DO3175D5 only: Single-lever mixer undersink
6 DO05755K only: Kitchen tap undersink
7 DO05855 and DO3185D5 only: Oversink fitting
Product description
The small water heater is only suitable for open (unpres-
surised) installation. It heats and stores drinking water up to
approx. 85 °C. Different temperature levels can be selected
with the temperature selector knob.
The appliance may not be operated with pre-heated water,
as otherwise the safety temperature limitation will trip.
The appliance is connected using the mains plug.
This installation and operating instruction manual describes
various appliance types:
– Undersink appliances with additional drip stop function
and pressure stop DO05705, DO05755K, DO3170D5,
DO3175D5 and DO05705CH
– Oversink appliances DO05805, DO05855, DO3185D5
and DO05805CH
Preparations for installation
I.
Shut off the water supply before connecting the appli-
ance.
Do n o t insert the mains plug.
Remove the installation bracket on the appliance and break
off the retaining rings (A).
Fix the connection cable to the rear of the appliance to suit
the required length (B).
en
Wall mounting
Undersink appliances DO05705,
II.
DO05755K, DO3170D5, DO3175D5 and
DO05705CH
Align the appliance on the wall and use the three indents
(top, left and right on the appliance) to apply markings
(A).
Connect the markings by a pattern of crossed lines with a
spirit level (B1 and B2).
Place the installation bracket on top at the point of inter-
section of the drawn lines and mark the position for the
holes (C).
Drill the holes and insert wall plugs (D1).
Attach the installation bracket (notch at top) to the wall
using the screws (D2).
Suspend the appliance in the installation bracket (D3).
Exchanging appliances
When replacing an old Siemens small water heater with
this new appliance, the existing drill holes with wall plugs
can be used. Please note that the new appliance is approx.
2 cm higher.
If the new appliance is to be flush at the top like the old ap-
pliance (E1):
Attach the new installation bracket to the wall with the
notches at the top.
If the new appliance is to be flush at the bottom like the old
appliance (E2):
Turn the installation bracket around and attach to the wall
with the notches at the bottom.
III. Oversink appliances DO05805,
DO05855, DO3185D5 and DO05805CH
Align the appliance on the wall and use the three indents
(top, left and right on the appliance) to apply markings
(F).
Connect the markings to a pattern of crossed lines with a
spirit level (G1 and G2).
Place the installation bracket on top at the point of inter-
section of the drawn lines and mark the position for the
holes (H).
Drill the holes and insert wall plugs (I1).
Attach the installation bracket (notch at top) to the wall
using the screws (I2).
Exchanging appliances
When replacing an old Siemens small water heater with this
new appliance, the existing drill holes with wall plugs can
be used. Please note that the new appliance is approx. 2 cm
higher.
Turn the installation bracket around and attach to the wall
with the notches at the bottom (J).
11