Bosch GWI 10,8 V-LI Professional Notice Originale page 13

Technical Data
Cordless angle drill/driver
Article number
Rated voltage
No-load speed
Max. torque for hard/soft screw-
driving application according to
ISO 5393
Torque adjustment range
Max. screw dia.
Max. drilling dia.
– Steel
– Wood
Weight according to
EPTA-Procedure 01/2003
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K =3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
Drilling into metal: a =2.5 m/s
h
2
Screwdriving: a =2.5 m/s
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2004/108/EC,
2006/42/EC.
Bosch Power Tools
GWI 10,8 V-LI
Professional
3 601 C60 9..
V=
-1
min 0 – 585
Nm
Nm 2.6 – 5.2
mm
mm
mm
kg
2 2
, K =1.5 m/s ,
2
, K =1.5 m/s .
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
10.8 Engineering
13/5
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
28.06.2011
5
Assembly
8
10
Battery Charging (see figure A)
Use only the battery chargers listed on the accessories
1.1
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
WARNING
tomatically switched off. The battery can be damaged.
To remove the battery 10 press the unlocking buttons 9 and
pull out the battery downwards. Do not exert any force.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
Changing the Tool (see figure B)
Before any work on the power tool, remove the battery.
Inserting
Pull the locking sleeve 1 toward the front and then push the in-
sert tool to the stop into the tool holder 2. The insert tool is au-
tomatically locked.
Removing
Pull the locking sleeve 1 forward and remove the insert tool.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
English | 13
Dr. Eckerhard Strötgen
Head of Product
Certification
Do not continue to press the On/Off
switch after the machine has been au-
1 609 929 R74 | (25.7.11)