Functional Description - Milwaukee M18 FUEL PACKOUT 0970-20 Manuel De L'utilisateur

FUNCTIONAL DESCRIPTION

1
4
1. Battery bay
2. Accessory storage areas
3. Motor housing
4. Battery compartment latches
5. Hose
6. Blower port
7. Tank latches (front and back)
8. PACKOUT™ feet
9. Tank
10. Switch
11. Inlet
12. PACKOUT™ lock
2
4
ASSEMBLY
WARNING
the battery pack before removing the tank.
CAUTION
Keep filter clean. Efficiency
of the vacuum is largely
dependent on the filter. A dirty filter will reduce
the air flow and overall efficiency of the system.
Remove from tank and tap clean.
WARNING
the battery. For specific charging instructions,
read the operator's manual supplied with your
charger and battery.
3
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
4
or removing accessories.
To insert the battery, slide the pack into the body
5
of the tool. Make sure it latches securely into place.
Removing/Installing the Filter
Use the filter for dry pickup only.
6
1. Remove the battery pack. Close and latch the
battery compartment.
2. Release the tank latches and lift off the motor
housing. Place it upside down on a flat surface.
7
3. To remove the filter, turn it 1/2" counter clockwise
and pull it off of the motor housing/float cage.
8
4. Empty all debris from the tank.
NOTE: When applicable, adhere to jobsite guide-
9
lines pertaining to the disposal of silica dust.
5. To install the filter, slide it over the float cage. Line
up the filter tabs with the motor housing notches
and turn it 1/2" clockwise to lock in place.
6. Replace the motor housing and secure both
latches.
Pick-Up/Blower
The vacuum can be used for debris pick-up or as a
blower, depending on the port used.
1. For the debris pick-up, insert the large end of the
10
hose into the intake port of the motor housing,
lining up the tabs on the hose with the notches in
11
the port. Twist to secure and form a tight fit.
2. To use as a blower, insert the large end of hose
into the blower port
up the tabs on the hose with the notches in the
port. Twist to secure and form a tight fit.
12
WARNING
mended for this tool. Others may be hazardous.
Installing/Removing the Accessories
To install the nozzles, hoses or extensions, push
the accessory onto the vacuum inlet.
Installing the Vacuum Power Tool Adapter
To install the vacuum power tool adapter, remove the
general cleaning nozzle by unscrewing it from the
end of the hose. Twist the power tool adapter onto
the exposed hose section until tight for a secure fit.
OPERATION
WARNING
To reduce the risk of
injury, always remove
proper eye protection marked to comply with
ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
To reduce the risk of fire and injury, do not use
Recharge only with the to pick up flammable or combustible materials.
charger specified for
To reduce the risk of injury, wear safety goggles
or glasses with side shields. Empty tank before
use.
Before use, ensure the filter and float cage are
properly installed. Remove filter before all wet
pick-up operations.
Starting and Stopping Vacuum
Always remove battery
To turn the vacuum on low, push the switch to the
pack before changing
Speed One (I) position.
To turn the vacuum on high, push the switch to the
Speed Two (II) position.
To turn off the vacuum, push the switch to the OFF
(O) position.
CAUTION
not shut off when the tank is filled, contact a
MILWAUKEE service facility for repairs. A mal-
functioning tool can cause personal injury or
property damage.
Wet Pick-Up Operation
For wet pick-up operation, it is recommended to use
the foam filter (Single pack, Cat. No. 49-90-2015).
1. Remove ALL dirt and debris found in the tank.
2. Remove the filter. Ensure that the float cage
remains in place.
of the motor housing, lining
3. A float cage shuts off suction when the tank is full.
Be sure that the float is clean and moves freely in
Only use accessories
the float cage to ensure that the float valve works.
specifically recom-
4. Turn on the vacuum and begin pick-up.
5. Turn off the vacuum immediately upon completing
a wet pick-up job or when tank is full and ready
to be emptied.
NOTE: If suction shuts off, turn off the vacuum
immediately and empty the tank.
6. Remove the battery pack.
7. Raise the hose to drain any excess liquid into
the tank.
8. Remove motor housing and pour liquid waste into
a suitable drain.
9. Clean the interior of the tank and pick-up acces-
sories periodically, more often when used to pick
up wet, sticky materials. Use warm, soapy water.
5
To reduce the risk of
injury, always wear
If the float is clean, moves
freely, and the suction does
Float cage