Milwaukee M18 CCS66 Notice Originale page 22

TECHNICAL DATA
Circular saw
Production code
No-load speed
Saw blade dia. x hole dia
Saw blade thickness
Max. Cutting depth at 0° / 45° / 50°
Battery voltage
Weight according EPTA-Procedure 01/2003 (4,0 Ah)
Noise information
Measured values determined according to EN 60 745. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 60745
GB
Sawing of wood Vibration emission value a
Uncertainty K
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745
and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications,
with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is run-
ning but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
WARNING!
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
CIRCULAR SAW SAFETY WARNINGS
Cutting procedures
a) DANGER: Keep hands away from cutting area and
the blade. Keep your second hand on auxiliary handle, or
motor housing. If both hands are holding the saw, they cannot
be cut by the blade.
b) Do not reach underneath the workpiece. The guard cannot
protect you from the blade below the workpiece.
c) Adjust the cutting depth to the thickness of the work-
piece. Less than a full tooth of the blade teeth should be visible
below the workpiece.
d) Never hold piece being cut in your hands or across your
leg. Secure the workpiece to a stable platform. It is impor-
tant to support the work properly to minimize body exposure,
blade binding, or loss of control.
English Deutsch
20
h,W
e) Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting tool may
contact hidden wiring. Contact with a "live" wire will also make
exposed metal parts of the power tool "live" and could give the
operator an electric shock.
f) When ripping, always use a rip fence or straight edge
guide. This improves the accuracy of cut and reduces the chance
of blade binding.
g) Always use blades with correct size and shape (diamond
versus round) of arbour holes. Blades that do not match the
mounting hardware of the saw will run eccentrically, causing loss
of control.
h) Never use damaged or incorrect blade washers or bolt.
The blade washers and bolt were specially designed for your saw,
for optimum performance and safety of operation.
Kickback causes and related warnings
– kickback is a sudden reaction to a pinched, bound or misaligned
saw blade, causing an uncontrolled saw to lift up and out of the
workpiece toward the operator;
– when the blade is pinched or bound tightly by the kerf closing
down, the blade stalls and the motor reaction drives the unit
rapidly back toward the operator;
M18 CCS66
4472 56 02 ...
... 000001-999999
5000 min
-1
190 x 30 mm
2,0 mm
67 / 48 / 46 mm
18 V
4,2 kg
83,2 dB(A)
94,2 dB(A)
2,0 m/s
2
1,5 m/s
2