KEUCO Royal Lumos 14597 171000 Instructions D'utilisation page 5

Technical data
– Power supply:
– max. Power consumption:
Prod. no.:
14597 171000:
14597 171500:
14597 XX2000:
14597 172500:
14597 173000:
14597 173500:
14597 XX4000:
14597 174500:
14597 XX5000:
– Protection rating:
– Ambient conditions:
Temperature
– Light colour
Mounting dimensions, see page 2.
Circuit diagram, see fi gure 1 on page 17.
Installation, see fi gure 2 onwards on page 17.
Operation
The mirror can be optionally actuated similar to a toggle
switch with a button on the mirror A or with an external
button B (operating mode I.) or switch B (operating
mode II.), see circuit diagram fi gure 1 on page 17.
Button functions
Button Function
Light on/off
• Pressing the button switches the mirror on with the
selected settings. The white LED goes off.
• Pressing the button again switches the mirror off.
The white LED lights up.
• The white LED can be deactivated.
– Switch on the mirror.
– Press and hold the button for 10 seconds.
- The lighting goes off.
- A short light impulse indicates that the white
LED was deactivated.
To switch the white LED back on, repeat the de-
scribed procedure.
Important information, please make sure to read!
230 V AC/ 50 Hz
Width Weight
460 mm 9.1 kg
650 mm 9.4 kg
700 mm 9.9 kg
800 mm 11.0 kg
900 mm 12.1 kg
1000 mm 13.2 kg
1050 mm 13.8 kg
1200 mm 15.4 kg
1400 mm 17.5 kg
5°– 40° C
2700 - 6500 Kelvin
A
Button Function
Front lighting
• The front and wall lighting is switched on by press-
Light
45 W
• Pressing the button again switches the light off.
48 W
50 W Washbasin lighting
53 W
• The washbasin lighting is switched on by pressing
57 W
60 W
• Pressing the button again switches the light off.
62 W
When both lightings are switched off, the mirror also
70 W
switches off.
77 W
Dimming the front and washbasin lighting
IP20
• Press the button when the mirror is switched on
The setting is stored and reproduced when switched
on again (only for connection type I, see fi gure 1 on
page 17).
Setting the light colour cooler
• Press and hold daylight white button and the light
• Release when the desired light colour has been
The setting is stored and reproduced when switched
on again (only for connection type I, see fi gure 1 on
page 17).
Adjusting light colour - daylight white (cool white)
• Press button and the colour temperature sets to
B
Setting the light colour warmer
• Press and hold warm white button and the light
• Release when the desired light colour has been
The setting is stored and reproduced when switched
on again (only for connection type I, see fi gure 1 on
page 17).
Adjusting light colour - warm white
• Press button and the colour temperature sets to
Replacement parts with order numbers, see page 19.
The light sources may only be replaced by the
manufacturer, its customer service or by an equally
qualifi ed person.
For information about warranty and maintenance, see
the enclosed Maintenance and Warranty Passport.
Disposal information! Equipment with this labelling
must not be disposed of in household refuse, but must
be disposed of at a collection centre intended for this
purpose.
ing the button when mirror is switched on.
the button when mirror is switched on.
and hold until the desired brightness or the end
value has been reached.
colour fades to cool white.
reached.
6500 Kelvin.
colour fades to warm white.
reached.
2700 Kelvin.
EN
5