Yamaha P50-m Mode D'emploi page 44

1.5 Program Change
1100nnnn Cn
Status
0ppppppp pp Program No. p=0~127
Program Change messages are not received when the Part
Parameter setting Rcv PROGRAM CHANGE = OFF.
When MIDI PROGRAM CHANGE TABLE = OFF, values
other than 0~28 are ignored.
1.6 Channel Aftertouch
1101nnnn Dn
Status
0vvvvvvv vv
Value
With the default settings, this has no function.
Channel Aftertouch messages are not received when the
Part Parameter setting Rcv CHANNEL AFTER TOUCH =
OFF.
1.7 Pitch Bend Change
1110nnnn En
Status
0lllllll ll
Value LSB
0mmmmmmm mm Value MSB
Pitch Bend Change messages are not received when the Part
Parameter setting Rcv PITCH BEND CHANGE = OFF.
2. Channel Mode Messages
2.1 All Sound Off
1011nnnn Bn Status
01111000 78
Control No.
00000000 00
Control Value
All sounding notes on the corresponding channel will be
silenced.
However the status of channel messages such as Note On
and Hold On will be maintained.
2.2 Reset All Controllers
1011nnnn Bn
Status
01111001 79
Control No.
00000000 00
Control Value
The values of the following controllers will change.
Controller Setting value
Pitch Bend Range +/–0 (center)
Channel Aftertouch 0 (off)
Polyphonic Aftertouch 0 (off)
Modulation 0 (off)
Expression 127(maximum)
Hold 0 (off)
Portamento 0 (off)
Sostenuto 0 (off)
Soft Pedal 0 (off)
Portamento Control Reset the Portamento Source
Note number that was received
RPN Number un-specified, internal
data not changed.
NRPN Number un-specified, internal
data not changed.
2.3 All Note Off
1011nnnn Bn Status
01111011 7B Control No.
00000000 00
Control Value
All notes of the corresponding channel that are currently on
will be turned off.
However if Hold1 or Sostenuto are on, the sound will con-
tinue until these are off.
2.4 Omni Off
n= channel number
2.5 Omni On
n= channel number
v=0~127
2.6 Mono
n= channel number
2.7 Poly
n= channel number
3. System Exclusive Messages
3.1 Parameter Changes
n= channel number
3.1.1
3.1.1.1 Master Volume
n= channel number
SOUND LISTS & MIDI DATA
1011nnnn Bn
Status
01111100 7C Control No.
00000000 00 Control Value
This performs the same processing as when All Note Off is
received.
1011nnnn Bn
Status
01111101 7D
Control No.
00000000 00
Control Value
This performs the same processing as when All Note Off is
received.
1011nnnn Bn
Status
01111110 7E
Control No.
00000000 00
Control Value
This performs the same processing as when All Sound Off
is received, and if the 3rd byte (the mono number) is in the
range 0~16, sets the instrument to Mode 4 (m=1).
1011nnnn Bn
Status
01111111 7E
Control No.
00000000 00
Control Value
This performs the same processing as when All Sound Off
is received, and sets the instrument to Mode 3.
This instrument receives the following parameter changes.
[ UNIVERSAL REALTIME MESSAGE ]
1) Master Volume
[ UNIVERSAL NON REALTIME MESSAGE ]
1) General MIDI Mode On
[ XG NATIVE ]
1) XG System on
2) XG System Data parameter change
3) Multi Effect1 Data parameter change
4) Part Data parameter change
[ P50-m NATIVE ]
1) P50-m System data parameter change
2) Remote switch
[ Other ]
1) Master tuning
Universal Realtime Messages
11110000 F0 Exclusive status
01111111 7F Universal Real Time
01111111 7F ID of target device
00000100 04 Sub-ID #1=Device Control Message
00000001 01 Sub-ID #2=Master Volume
0sssssss ss Volume LSB
0ttttttt tt Volume MSB
11110111 F7 End of Exclusive
Alternatively,
11110000 F0 Exclusive status
01111111 7F Universal Real Time
0xxxnnnn xn Device No.xxx = don't care
n= channel number
n= channel number
n= channel number
n= channel number
35